Electrical Safety; Assembly And Setting Up; Description And Package Contents - IKRA EVL 1500 Manuel D'utilisation

extreme care before lifting your Machine for and
during transportation.
• Never pick up or carry your Machine while the motor
is running. If you do have to then make sure the
rotating parts have stopped.
• Never operate your Machine with defective guards or
shields.
• Store your Machine in a dry place when not in use,
out of the reach of children.
• Do not use solvents or cleaning liquids to clean your
Machine - use a blunt scraper to remove grass and
dirt. Always disconnect from the electrical supply
before cleaning.
• Do not operate your Machine if any parts are
defective; discard all defective parts and fit new parts
before use.
• Keep all nuts, bolts and screws tightened to be sure
your Machine is in a safe working condition.

5. ELECTRICAL SAFETY

• The electric motor has been designed to use single
phase voltage only.
• Make sure your voltage corresponds to the one
written on the rating label.
Your machine has double insulation in
conformity to Directive EN 60335, you do
not therefore need to earth.
• Always use a plug compulsory for double insulation
electric tooling when replacing the cable.
• Always switch your machine off before disconnecting
any plug, socket or extension.
• Increased safety can be obtained by having a
qualified electrician install a high sensitivity (30mA)
circuit breaker in the house wiring. If you do not have
such a circuit breaker installed, or you do not wish
to have one installed, then we strongly recommend
that the electrical power to your Machine be supplied
through a high sensitivity (30mA) residual current
device (RCD). The RCD is designed to provide a high
degree of personal protection against harmful electric
current should fault conditions occur.
The use of an RCD or other circuit breaker
unit does not release the operator of your
Machine from the safety instructions
and safe working practices given in this
manual.
• When using an extension, make sure that it has been
certified and is the right size for conveying electricity
supply to the equipment (see technical specifications).
• Smallest size of lead is 1.5 mm². Completely unwind
the cable if you are using a winder.

6. DESCRIPTION AND PACKAGE CONTENTS

The package contains (Fig. 1):
• 1 Machine body fitted with: lever to adjust height
of wheels (1), safety cover (2) and blade system of
scarifier(3)
All manuals and user guides at all-guides.com
• 1 upper handle bar(4) fitted with: switch with cable and
switch release button (5), switch lever (6) and socket
to connect extension (7)
• 1 middle handle bar(8)
• 2 lower handle bars (9) fitted with: plastic holder (10)
and knobbed bolt(11)
• 2 cable clamps (12)
• 2 sets of winged nut and bolts(13) to fix middle handle
bar to lower handle bar
• 2 sets of knob nut and bolts(14) to fix upper handle bar
to middle handle bar
• 1 hook to hold extension (15)
• 1 set of grass bag(16)
• 1 set of blade system of lawn raker(17)
• 1 hexagon socket wrench (18) to change the blade
system
NOTE: make sure that the Machine and accessories in
the package are not damaged

7. ASSEMBLY AND SETTING UP

Always disconnect plug from mains before
assembly and setting up
HANDLE ASSEMBLY (Fig. 2)
• Insert the knobbed bolt of lower handle bar (9) from
outside in the two holes in the machine body and
screw the knobbed bolt to fix it (Fig. 2.1).
• Join the middle handle bar (8) to the lower handle
bar (9) by means of the winged nuts and bolts (13)
provided (Fig. 2.2).
• Fit the cable hook (15) onto the upper handle bar from
the switch side (Fig. 2.3).
• Join the upper handle bar (4) to the middle handle
bar (8) by means of the knobbed nuts and bolts (14)
provided ( Fig. 2.4).
• Fix the cable to the handle by the clamps (12) (Fig.
2.5).
GRASS BAG ASSEMBLY (Fig. 3)
• Insert the front metal frame into the rear metal frame
(Fig. 3.1).
• Fix the front metal frame inside the clamping rims of
cloth-bag (Fig. 3.2).
• Mount the grass collector bag as shown in the picture
(Fig. 3.3).
HEIGHT ADJUSTMENT (Fig. 4)
• Use the adjustment arm (1) of the machine body for
adjusting height of wheels to select the height for
working.
• Pull the adjustment arm (1) away to move it along the
slot ( Fig. 4.1).
• Select regulation from among the 4 options.
• Release and Insert the adjustment arm (1) into the
GB-4