Telwin DRIVE 13000 Manuel D'utilisation page 4

heaters, near flames or in other hot areas.
- Only use the charger supplied with the device to charge
the starter.
- Do not throw the starter into a fire or heat it up.
- Do not invert the positive "+" and negative "-" connection
polarities.
- Do not short-circuit the starter terminals.
- Do not perforate the starter casing with drill bits, do not
hit it with a hammer or stand on it.
- Do not position the starter inside stoves, microwave
ovens etc.
- Do not throw the starter or cause high impacts.
- Do not modify or tamper with the starter casing.
- Refrain from using the starter if it emits strange smells,
heats up or deforms during use, charging or storage.
- If the starter emits strange smells or leaks acid,
immediately move the device away from any heat
sources or free burning flames.
- In case of contact of the starter battery acid on the skin
or clothing, rinse with copious amounts of water.
- In case of contact of the starter battery acid with the
eyes, rinse immediately with copious amounts of water
and call a doctor.
Keeping this manual.
The manual should be read, paying attention to all the
warnings and safety precautions to be taken when using
and maintaining the device, the list of components and all
technical specifications.
Please keep this manual in a secure and dry place for future
reference.
2. INTRODUCTION AND GENERAL DESCRIPTION
Intended use
Multi-functional, portable, battery-powered starter. Ideal
for anyone needing an emergency starter. Its applications
include use on motorcycles, automobiles, boats and many
more.
Fully compatible with any 12-volt starter system.
The starter uses LITHIUM BATTERIES; this makes the
device extremely compact and easy to handle.
The multi-functional starter is also equipped with a
powerful LED light and four outputs to power and/or
charge 5V/12V/19V electronic devices.
Description (figure A):
A-1. Book type pack.
A-2. Multifunctional starter.
A-3. Starter clamps.
A-4. 12V/10A and 19V/3.5A output cable.
A-5. Charger cable with cigarette lighter type 12V jack
plug.
A-6. Adaptor cable to connect the USB port on the
device to various power and/or charge inputs on
the main commercially available electronic devices.
A-7. Output adaptors for the A-4 cable.
A-8. Charging power unit.
A-9. Starter charging input.
A-10. 12V/10A output.
A-11. 5V/1A and 5V/2.1A USB ports.
A-12. 19V/3.5A output.
A-13. LED lights.
A-14. Starter clamps outs (ref. A-3).
A-15. ON/OFF switch for the charge level, the output
ports (ref. A-11 and 12) and the LED lights.
A-16. Internal battery charge status indicator LED.
3. INSTALLATION
POSITIONING THE STARTER
When using the starter, position it on a horizontal, flat and
stable surface.
4. OPERATING INFORMATION
4.1 How to use the starter:
always in the order given below!
Always prevent the black and red clamps from touching
each other or a common cable!
- Make sure that the vehicle or boat to be started is
switched off (switch or ignition key in the OFF position).
- Connect the red clamp POS. (+) to the battery terminal
POS. (+), then connect the black clamp NEG. (-) to the
vehicle chassis or the battery terminal NEG. (-).
WARNING: failure to follow these rules may
compromise the operating life of the device:
- Turn the vehicle ignition to the start position for no
more than 3 seconds.
- If the vehicle or boat does not start, wait at least 15
seconds before trying again.
- If the vehicle or boat still does not start, wait at least
2 minutes before trying again.
After a successful start, with the engine running, follow the
sequence of instructions below with great care:
- Disconnect the black clamp (negative) from the vehicle.
- Disconnect the red clamp (positive) from the vehicle.
- Remove the starter cable connector from the starter
- Replace the cables and the starter in their seats inside
the case.
It is highly recommended to recharge the starter as soon
as possible.
4.2 Using the starter as a power and/or charging device:
- Select the output cable (fig. A-4 or fig. A-6) with the
terminal suitable for the device to be powered (fig. A-7)
according to the required voltage/current;
- Insert the cable terminal into the appropriate output
port on the starter (fig. A-10, 11, 12);
- Press the ON button seen in figure A-15
- Insert the other cable terminal into the device to be
- 4 -
WARNING: follow
instructions meticulously,
these
and