Publicité
2. Warnings and safety instructions.
Operator safety
En
IMPORTANT: A dust filter mask should be
worn during operation.
Always wear a safety face shield or goggles.
Always wear heavy, long pants, boots and
gloves. Do not wear loose clothing, jewelry,
short pants, sandals or go barefoot. Secure
hair so it is above shoulder length.
Do not operate that tool when you are tired, ill
or under the influence of alcohol, drugs or
medication.
Never let a child or inexperienced person
operate the machine.
Wear hearing protection.
Never start or run the engine inside a closed
room or building. Breathing exhaust fumes
can kill.
Keep handles free of oil and fuel.
Keep hands away from moving parts or
heated area.
Do not grab or hold the unit by the blow pipe.
When the unit is turned off, make sure the
engine has stopped before the unit is set
down.
When operation is prolonged, take a break
from time to time so that you may avoid
possible whitefinger disease which is caused
by vibration.
Tool safety
Inspect the entire tool before each use.
Replace damaged parts. Check for fuel leaks
and make sure all fasteners are in place and
securely fastened.
Replace parts that are cracked, chipped or
damaged in any way before using the tool.
Make sure the safety guard is properly
attached.
Keep others away when making carburetor
adjustments.
Use only accessories as recommended for
this tool by the manufacturer.
WARNING!
Never modify the tool in any way. Do not use
the tool for any job except that for which it is
intended.
Fuel safety
NOTE!
Empty the fuel tank before storing the tool.
Especially, in case of over three month
storage, it is a must otherwise fuel may
corrode causing carburetor damage. It is
recommended that the fuel be emp-tied
after each use. If fuel is left in the tank,
store so fuel will not leak.
Mix and pour fuel outdoors and where there
are no sparks or flames.
Use a container approved for fuel.
Do not smoke or allow smoking near fuel or
the tool or while using the tool.
Wipe up all fuel spills before starting engine.
Move at least 3 m away from fueling site
before starting engine.
Stop engine before removing fuel cap.
Store tool and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
WARNING!
Antivibration systems do not guarantee that
you will not sustain whitefinger disease or
carpal tunnel syndrome. Therefore, continual
and regular users should monitor closely the
condition of their hands and fingers. If any of
the above symptoms appear, seek medical
3
All manuals and user guides at all-guides.com
advice immediately.
Blowing safety
Operate power equipment only at reason-
able hours-not early in the morning or late at
night when people might be disturbed.
Comply with times listed in local ordinances.
Usual recommendations are 9:00 a.m. to
5:00 p.m., Monday through Saturday.
Never direct discharge of air toward by-
standers nor allow anyone near the area of
operation. Use care in directing discharge to
avoid glass,enclosures, automobiles, etc.
Stay alert for uneven sidewalks, holes in
terrain or other unstable condition when using
the tool.
Take all possible precautions when leaving
the tool unattended such as stopping the
engine.
Never operate the tool without guards, blow
pipes or other protective device in place. (If
so equipped.)
Keep others including children, animals,
bystanders and helpers outside the 15 m
hazard zone. Stop the engine immediately if
you are approached.
Always keep the engine on the right side of
your body. (Hand held blower only)
Keep firm footing and balance. Do not over-
reach.
Keep all parts of your body away from the
muffler.
Maintenance safety
Maintain the tool according to recommended
procedures.
Disconnect the spark plug before performing
maintenance except for carburetor adjust-
ments.
Keep others away when making carburetor
adjustments.
Use only genuine replacement parts as
recommended by the manufacturer.
Transport and storage
Carry the tool by hand with the engine
stopped and the muffler away from your
body.
Allow the engine to cool, empty the fuel tank,
and secure the tool before storing or
transporting in a vehicle.
Empty the fuel tank before storing the tool. It
is recommended that the fuel be emptied
after each use. If fuel is left in the tank, store
so fuel will not leak.
Store tool out of the reach of children.
Clean the unit carefully and store it in a dry
place.
Make sure engine switch is off when
transporting or storing.
If situations occur which are not covered in
this manual, take care and use common
sense. Contact your dealer if you need
assistance.
Pay special attention to statements preceded
by the following words:
WARNING!
Indicates a strong possibility of severe per-
sonal injury or loss of life, if instructions are
not followed.
CAUTION!
Indicates a possibility of personal injury or
equipment damage, if instructions are not
followed.
NOTE!
Helpful information for correct function and
use.
Publicité
