Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
OBJ_BUCH-2819-002.book Page 3 Monday, May 22, 2017 11:27 AM
Setting the Assistance Level
On the on-board computer you can set how much the eBike
drive assists you while pedalling. The assistance level can be
changed at any time, even while cycling.
Note: For individual versions, it is possible that the assistance
level is pre-set and cannot be changed. It is also possible that
less assistance levels are available for selection than listed
here.
When the eBike is configured in "eMTB Mode" by the manu-
facturer, the assistance level "SPORT" is replaced by
"eMTB". In "eMTB Mode", the assistance factor and torque
are dynamically adjusted as a function of the force you exert
on the pedals. "eMTB Mode" is only available for
Performance Line CX drives.
The following assistance levels (max.) are available:
– "OFF": The motor assistance is switched off, and the eBike
can be moved as a normal bicycle only by pedalling. The
push assistance cannot be activated in this assistance
level.
– "ECO": Effective assistance at maximum efficiency for
maximum cruising range
– "TOUR": Uniform assistance, for touring with long cruising
range
– "SPORT"/"eMTB":
"SPORT": Powerful assistance for sportive riding off road
as well as for urban traffic
"eMTB": Optimal assistance whatever the terrain, rapid
acceleration when starting from a standstill, improved
dynamics and top performance.
– "TURBO": Maximum assistance, supporting highest
cadence for sportive riding
To increase the assistance level, short-press
"+" 6 on the on-board computer repeatedly until the required
assistance level appears in indicator i. To decrease the assis-
tance level, short-press
the button "–" 5.
Switching bike lights on/off
In the version which has the bike lights powered by the eBike
system, medium-press
the button "+" to switch on the
front and rear lights at the same time. To switch off the bike
lights, long-press
the button "+".
The lighting symbol h is displayed when the light is on.
Switching the bike light on and off has no effect on the back
lighting of the display.
68
Displays and configurations of the on-board
computer
Speed and Distance Indication
The speed indication a always displays the current speed.
Indicator i always displays the last setting as standard. Re-
peatedly medium-press
distance "TRIP", the total distance "TOTAL" and the range of
the battery pack "RANGE" one after the other. (Short-
pressing
the button "–" will decrease the assistance
level!)
The trip distance "TRIP" is reset by simultaneously long-
pressing
the buttons "+" and "–". The display will initially
show "RESET". If you continue to press both buttons, the trip
distance "TRIP" will be set to "0".
You can switch the displayed values from kilometres to miles
by holding down button "–"
On/Off button 1
The versions of the subsystems can be displayed for the pur-
poses of servicing. With the system switched off, simultane-
ously press buttons "–" and "+" and then press the On/Off
button 1 .
The USB socket is reserved for connecting diagnostic
systems. The USB socket does not have any other function.
The USB connection must always be completely sealed
with the protective cap 8.
Action
Switch on on-board computer
Switch off on-board computer
Increase assistance
the button
Decrease assistance
Display "TRIP", "TOTAL", "RANGE",
assistance modes
Switch on bike lights
Switch off bike lights
Reset trip distance
Activate push assistance
Perform push assistance
Switch from kilometres to miles
Display the versions
Set display brightness
1) The eBike system must be switched off.
2) The information is shown as scrolling text.
3) The display must be switched off.
the button "–" to display the trip
and briefly pressing the
.
Buttons Duration
Any
Any
+
–
–
+
+
– +
WALK
1.
+
2. Any
–
1. Hold
2.
1)2)
– +
1. Hold
2.
3)
– +
1. Hold
2.
– or +
Publicité
Table des Matières
