Assembly And Adjustments; Installing And Removing The Battery Pack - DeWalt DCE200 Guide D'utilisation

FIG. C
20
When the battery state of charge LED
color, the tool is ON.
D WALT CRIMP CONNECT™ System (Fig. A)
e
This press tool is capable of connecting with a computer
via the micro USB port 9 on the back of the tool using the
micro USB cable included with your tool. This allows the
user to connect the D WALT press tool to a computer which
e
utilizes D WALT's CRIMP CONNECT
e
NOTE: The CRIMP CONNECT™ System software is governed
by separate terms and conditions available for viewing
through the software download.
Step 1: Download the CRIMP CONNECT™ System software
to your computer at www.dewalt.com/crimpconnect.
Step 2: Follow the instructions in the software to create
your CRIMP CONNECT™ System account.
Step 3: Connect your press tool with the D
CONNECT™ System software by first connecting the
provided micro USB cable to the micro USB port
back of the tool to a USB port on a computer. Then go to
the Home screen of the program to access tool tracking and
usage reports stored on the press tool.
NOTE: The USB connection will not charge the tool's
battery pack.
For more information on D WALT CRIMP CONNECT™ System
e
functionality and features, please call 1–800–4-D
(1–800–433–9258), visit www.D
page and help screens located inside the software.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: To reduce the risk of serious personal
injury, do not use the press tool with any kind
of accessory or attachment other than those
recommended by D WALT.
e
Replacing the Press Jaw (Fig. D)
1. Remove the battery pack.
2. Hold the jaw and move the lock/release slide
1
The jaw retention pin 3
releasing the jaw.

CAUTION: The jaw 1
4 is moved while the jaw is aimed downward.
3. Remove the press jaw or attachment.
8
17
18
19
19 is lit, regardless of
System software.
TM
WALT CRIMP
e
9 on the
WALT
e
WALT.com or view the FAQ
e
back.
4
will automatically spring open,
will fall if the lock/release slide
4. Replace with a new or different sized press jaw or
attachment as shown in Figure D.
5. Push the jaw retention pin
closed position.
NOTICE: To avoid damage to the tool, do not
operate the tool without the jaw retention pin
fully inserted. Damage to the tool may occur.
FIG. D
1
4
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: CUT OR AMPUTATION HAZARD. Never
have any part of your body near the press jaw or
moving parts during the press cycle, or whenever the
main power is ON. Serious personal injury may occur.

WARNING: Proper material preparation
and installation is the responsibility of the
installing contractor.

WARNING: The press fittings must be used in
compliance with applicable building codes
and as approved by the authorities having
jurisdiction. For proper installation procedures
and to reduce the risk of failure resulting in injury or
property damage, follow all published safety and
installation instructions.

WARNING: To reduce the risk of injury, always
remove the press jaw or attachment for
transport or storage.

Installing and Removing the Battery Pack

(Fig. E)
NOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack into the tool handle, align the
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
3 back in until it locks in a
3
9