stayer SCC 315 Instructions D'emploi page 18

Start-up and shut-off when using mitre saw/lower cutting
table
Start-up: Press and hold the rectangular switch (12) on the
handle to engage the motor.
Shut-off: Release the rectangular switch.
Start-up and shut-off when using the upper cutting table
with automatic interlocking (13)
Start-up: Press the green button I.
Shut-off: Press the red button O
Use of the lower cutting table
Warning!
1
The risk of accidents due to a contact with the cutting
disk appearing at the upper table. For your own safety,
carry out the following preparation before working with
the lower table.
2
It is mandatory to carry out any settings with the cable
unplugged.
WARNING
IF YOU DO NOT INSTALL THE LATERAL GUIDE/GUARD
(16) OF THE UPPER TABLE IN SUCH A WAY THAT IT
ENGAGES THE UPPER SAFETY LOCKING SYSTEM (14)
THE MACHINE WILL NOT OPERATE.
Safety preparation of the upper cutting table for
cutting on the lower table.
1 If the machine is in the down position, pull the pin (5),
turn it 90° to unlock the head (F) and lift it to its vertical
position. If the machine has a lower guard in place (2),
remove it and set it aside.
2 Install the lateral guide/guard (16) of the upper table on
the upper blade guard (17) so that its front side rests and
engages the safety button of the lower table (14). Tighten
the knob holding the guard in place (16). The machine
cannot operate as a mitre saw/lower cutting table if
the button (14) is not engaged and locked. This button
disables the on/off interlock switches (13) and enables
the use of the switch (12) on the grip.
Cutting operation with the lower cutting table
Warning!
1 Respect the limits regarding the size and material of the
workpiece.
2 Use clamps to fasten the workpiece whenever possible.
Y
Preparation for horizontal angled cutting on the
lower table
To select the desired angle follow the steps below:
Mitre cutting (X axis = -45° / +60°, Y axis = 90°)
Y
Mitre cutting occurs when the head stays in a vertical position,
perpendicular to the lower cutting table.
The head can rotate on its axis from -45° to +60°.
To adjust the mitre angle, loosen the angle selector knob (1)
and use it to rotate the lower cutting table (A) to the desired
angle.
Y
The lower cutting table has a plate that marks the angle on
the scale ruler of the lower table.
Once you have found the desired cutting angle, tighten the
X
X
X
ENGLISH
18
angle selector knob (1).
In addition, the lower table is designed to allow easy angle
adjustment -45° / -30° / -15° / -7.5° / 0° / +15° / +30° / +60°.
To take advantage of these pre-sets, loosen the knob (1).
The table will continue to rotate as you push the knob (1) and
will stop automatically when it reaches any of the indicated
angles, halting at each angle until you engage the knob (1)
again.
Bevel cutting (X axis = 90º, Y axis = -45° / 0°)
Y
Y
Bevel cutting occurs when the head tilts on its axis and no
longer remains perpendicular to the lower cutting table.
Bevel cutting occurs when the head tilts on its axis and no
longer remains perpendicular to the lower cutting table. This
tool only allows the head to swing to the left side.
Y
To adjust the bevel cut angle, loosen the head tilt knob (8) and
tilt the head to the desired angle.
The machine is set to tilt to -45° by default.
Y
Use the scale ruler located next to the knob (8) to fine-tune
the cutting angle.
Once you have found the bevel cutting angle, retighten the
knob (8).
Compound cutting (X axis = -45° / +45°, Y axis = -45° / 0°)
Y
Y
Compound cutting involves a combination of bevel and mitre
cutting angles.
To find your compound cut, follow the steps indicated for
performing bevel and mitre cuts simultaneously.
Carrying out the cutting operation on the lower
table
1
Prepare workpiece by fastening it in a completely safe
manner.
2
Start the electrical machine by pushing switch.
3
Wait for some seconds until the cutting disk reaches its
maximum speed.
4
Slowly lower the operating head by a continuous manner
and without jerks, using hand grip.
5
Exert pressure in the blade's direction of advance with an
intensity being suitable for the material to be cut.
6 Once the cutting operation has been completed, raise
operating head again. Stop the machine by pushing
switch.
Using extension brackets (H) for long cuts
The SCC315 tool includes 2 extension brackets for cutting
long workpieces (H).
The brackets are inserted into the slots (9) and secured with
a knob located next to the clamp inserts (10).
18
X
X
X
X
X
X