General Safety Instructions; Intended Use; Residual Risks - Scheppach Ox 3-1200 Traduction Du Manuel D'origine

Only the operator is allowed in the work area
of the machine. Keep other people and ani-
mals (minimum distance 5 m) at a distance.
Do not remove jammed trunks with your
hands.
Caution! Switch off the engine before repair,
maintenance and cleaning. Unplug the mains
plug.
Danger of bruising and injury from sharp
edges; never touch danger areas when the
cleaver is moving.
High-voltage, danger to life!
The machine must only be operated by one
person!
Loosen the vent bolt two revolutions, before
2x
Oil
starting work. Close before transport.
Oil
2x
1. 2.
Caution! Moving machine parts!
Do not transport the device in the horizontal
position!
Familiarise yourself with the two-hand control before
operating the machine! Read the operating instructions
thoroughly.
Additional warnings without symbols:
• Do not remove the casing.
In this operating manual, points concerning your safety will
be marked with this symbol: m
m General Safety Instructions
WARNING: If you use electric tools, you should observe the
general safety measures mentioned below in order to reduce
the risk of fire, electric shock, and personal injury.
Please read all instructions before working with these tools.
• Observe all safety instructions and warnings for the
machine.
• Keep all safety instructions and warning labels on the
machine complete and in legible condition.
• You must not remove the safety devices on the ma-
chine or make them inoperative.
• Inspect the power cords. Do not use faulty power cords.
• Check that the two-hand control is functioning cor-
rectly before operation.
• The operator must be at least 18 years of age. Trainees
must be at least 16 years old, but may only work with
the machine under supervision.
• Wear work gloves during work.
• Attention during work: injury hazard to fingers and
hands.
• When splitting heavy or bulky materials, use appropri-
ate appliance for support.
• Switch motor off for retooling, adjustment, and clean-
10 english
All manuals and user guides at all-guides.com
ing, as well as for maintenance and troubleshooting.
Pull power plug!
• Installation, repairs and maintenance work on the elec-
trical installation may only be carried out by qualified
personnel.
• All guards and safety mechanisms must be reinstalled
immediately after completing the repairs or the main-
tenance work.
• Switch the motor off when leaving the working area.
Pull power plug!
Additional Safety Instructions for Log Splitters
• The log splitter may only be operated by a single per-
son.
• Wear protective gear (protective goggles/mask, gloves,
hearing protection, and safety shoes) to protect against
possible injuries.
• Never split logs with nails, wire or other objects in
them.
• Logs already split and shavings pose a threat within the
working area. There is the risk of tripping, slipping, or
falling. Always keep the working area tidy.
• Never put your hands on moving parts while the ma-
chine is switched on.
• Only split logs with a maximal length of 1,300 mm.
• Before starting work, check the hydraulic lines and
hoses.
• Check protective units and functions of the machine.
• Do not put your hands into the splitting area.
• Should the wood jam, turn the machine off and remove
the wood carefully.
m Intended Use
This machine complies with the current EC machinery direc-
tive.
• The hydraulic log splitter is designed for "stationary
operation", logs may only be split standing upright and
along the grain. The dimensions of the logs to be split:
wood length: 60/96,5/104/133 cm
ø min/max: 10/40 cm
• Never split logs lying horizontally or across the grain.
• The manufacture's safety, working, and maintenance
instructions as well the dimensions stated in the tech-
nical specifications must be observed.
• The applicable rules for accident prevention and other
generally accepted rules concerning safety must be
obeyed.
• The machine may only be operated, serviced, or re-
paired by persons familiar with it and aware of the
risks. Arbitrary modifications of the machine exclude
any liability of the manufacture for damages arising
from this.
• The machine may only be used with original accesso-
ries and original tools from the manufacturer.
• Every other use will be considered to be unintended
use. The manufacturer assumes no liability for dam-
ages arising from this and it will be solely at the opera-
tor's own risk.
m Residual Risks
The machine was designed according to the state of the
art and accepted safety standards. However, residual risks
might occur during work.
• Risk of finger or hand injury by the cutting knife due
to improper guidance or placement of the log.