Bosch Professional GCM 216 Notice Originale page 20

20 | English
ted supply. Use of an RCD reduces the risk of electric
shock.
Personal safety
Stay alert, watch what you are doing and use common
u
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious per-
sonal injury.
Use personal protective equipment. Always wear eye
u
protection. Protective equipment such as a dust mask,
non-skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce personal in-
juries.
Prevent unintentional starting. Ensure the switch is in
u
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or en-
ergising power tools that have the switch on invites acci-
dents.
Remove any adjusting key or wrench before turning
u
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal in-
jury.
Do not overreach. Keep proper footing and balance at
u
all times. This enables better control of the power tool in
unexpected situations.
Dress properly. Do not wear loose clothing or jew-
u
ellery. Keep your hair and clothing away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
If devices are provided for the connection of dust ex-
u
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
Do not let familiarity gained from frequent use of tools
u
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe in-
jury within a fraction of a second.
Power tool use and care
Do not force the power tool. Use the correct power
u
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was de-
signed.
Do not use the power tool if the switch does not turn it
u
on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or re-
u
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and
u
do not allow persons unfamiliar with the power tool or
1 609 92A 72R | (15.11.2021)
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for mis-
u
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Safety Warnings for Mitre Saws
Mitre saws are intended to cut wood or wood-like
u
products, they cannot be used with abrasive cut-off
wheels for cutting ferrous material such as bars, rods,
studs, etc. Abrasive dust causes moving parts such as
the lower guard to jam. Sparks from abrasive cutting will
burn the lower guard, the kerf insert and other plastic
parts.
Use clamps to support the workpiece whenever pos-
u
sible. If supporting the workpiece by hand, you must
always keep your hand at least 100 mm from either
side of the saw blade. Do not use this saw to cut pieces
that are too small to be securely clamped or held by
hand. If your hand is placed too close to the saw blade,
there is an increased risk of injury from blade contact.
The workpiece must be stationary and clamped or
u
held against both the fence and the table. Do not feed
the workpiece into the blade or cut "freehand" in any
way. Unrestrained or moving workpieces could be thrown
at high speeds, causing injury.
Push the saw through the workpiece. Do not pull the
u
saw through the workpiece. To make a cut, raise the
saw head and pull it out over the workpiece without
cutting, start the motor, press the saw head down and
push the saw through the workpiece. Cutting on the
pull stroke is likely to cause the saw blade to climb on top
of the workpiece and violently throw the blade assembly
towards the operator.
Never cross your hand over the intended line of cut-
u
ting either in front or behind the saw blade. Supporting
the workpiece "cross handed" i.e. holding the workpiece
Bosch Power Tools