Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Figure 16
Start Your Appliance
Your refrigerated drawers have been fitted with a Sentry Sys-
tem™ refrigeration monitor. It is located at the top front of the
cabinet and can be accessed by opening the top drawer. Your
appliance will start upon initial plug-in. On start the Sentry
System™ monitor will flash amber. This is normal. Press the "ON/
OFF" button and the appliance resets and the LED turns green.
(Refer to Figure 15 above). To turn the unit ON/OFF, press and
hold the "ON/OFF" key for a minimum of 5 seconds.
Set Your Temperature Mode
This product can display either Fahrenheit or Celsius. To do so,
press the "
F/C" button on the display panel to change from one
°
to the other.
Set the desired temperature
The available temperature range of the unit is from 33° to 47°F
(1° to 8° C). This range allows flexibility of temperature prefer-
ences and provides the ideal storing and serving temperatures.
The temperature is initially set in the factory at 37° F (3° C). The
temperature set point can be lowered or raised by first pushing
the "SET" button on the display pad. A "SET" icon will be dis-
played in the temperature display. Pressing and releasing either
the "WARMER" or "COLDER" buttons located on the display pad
will raise or lower the set temperature by one (1) degree at a
time. As with any refrigeration product, there will be slight tem-
perature variance at different locations within the cabinet.
Load Your Appliance
Load your appliance with your desired items. Please note that
it may take up to 24 hours for your refrigerator to reach the de-
sired temperature once loaded. This will primarily depend on the
amount of contents loaded into the refrigerator and the amount
of opening and closings of the drawers. Consider this when
initially loading the drawers. Best results will be obtained by first
allowing the drawers to "pull down" to your set temperature
before loading the drawers.
Interior Light
The upper and lower interior lights make it easy to view your
food and beverages. The light will always come on when either
drawer is opened, except when unit is in Sabbath Mode.
Defrost Cycle
In order to maintain optimal performance, your refrigerator must
periodically enter a defrost cycle to clear frost buildup. During
the defrost cycles, the display will show DEF, and changes to
setpoint and °F/°C setting may not be made.
USING YOUR REFRIGERATOR DRAWERS
ON
OFF
Press and hold
Warmer
Set
F/C
Colder
Sabbath Mode
Your refrigerated drawers are equipped with a Sabbath Mode
feature. By activating this mode, you will be disabling all dis-
plays, audible alarms and lights. To activate the Sabbath Mode,
press and hold the "SET" button while pressing the "
four (4) times within seven (7) seconds. To disable the Sabbath
Mode, repeat the process. The Sabbath Mode will deactivate
automatically after 72 hours.
Warning Alarms
The Sentry System™ monitor will let you know if your unit is not
functioning properly for the following reasons. Door ajar, high or
low temperature, and power failure. These alarms are explained
below.
Door Ajar Alarm
If the drawer has been left open for over five (5) minutes, the
alarm will sound and the LED will flash green. This will stop as
soon as the drawer is closed, or can be reset by pressing the
"ON/OFF" button.
High and Low Temperature
If your unit reaches temperatures outside normal operating
temperatures for your set point for more than one (1) hour, an
alarm will sound and the LED will flash red. This will warn you
that your contents have seen temperatures that may not be con-
ducive for long-term storage. This alarm can be reset by pressing
the "ON/OFF" button.
Power Failure
If your unit experiences a power failure, the LED will flash amber
until the alarm is reset by pressing the "ON/OFF" button.
Reset Alarms
Press the "ON/OFF" button for approximately one (1) second.
This will reset all audible and display alarms when the button is
released.
Enable/Disable Sentry System™ Alarms
Press and hold the "SET" key for five (5) seconds to enable or dis-
able the Sentry System™alarms. LED will display a steady green
when enabled or a steady amber when disabled.
Quick Reference Guide
The quick reference guide on page 15 and 16 can be removed
from this manual and retained near the appliance for quick ac-
cess to the Sentry System™ functions.
14
Sentry System™
Power Failure-Flashing Amber
High/Low Temp-Red
LED
Press ON/OFF-Reset
Alarms OFF-Steady Amber
F/C" button
°
Publicité
Chapitres
Table des Matières
