Craftsman C935-51421 Guide D'utilisation page 5

- Temporarily park the line in the holding
slots (23) on one side of the spool as
shown in the inset in Fig. 11.
• Repeat the above procedure for the
second cutting line on the lower
section of the spool.
• Fit the spool onto the tool as described
in Fitting a New Spool of Cutting Line.
CAUTION: Before you begin trimming,
only use the appropriate type of
Craftsman cutting line. Ensure that
cutting line is present in both sections
of the spool. Fig. 9.
10
11
24
23
23
12
25
28
27 26
FITTING THE HDL CASSETTE (FIG. 12)
Your trimmer is shipped with the AFS
cassette installed. To fit the HDL (Heavy
Duty Line) cassette, proceed as follows:
• Unplug the tool.
• Keep the tabs (18) depressed and
remove the AFS cassette (19) from the
cassette housing (12) in the trimmer
head. Fig. 8.
• Make sure a piece of heavy cutting line
is correctly fitted to the HDL cassette,
as described in Fitting a New Piece of
Heavy Duty Cutting Line below. Fig. 12.
• Align the tabs on the HDL cassette
with the slots (22, Fig. 8) in the
cassette housing.
• Push the HDL cassette into the housing
until it snaps securely into place.
FITTING A NEW PIECE OF HEAVY
DUTY CUTTING LINE (FIG. 12)
Replacement pieces of heavy duty
cutting line are available from your
Craftsman dealer. Please call 1-800-4-
MY-HOME for more information. To fit a
new piece of cutting line, proceed as
follows:
• Unplug the trimmer from its power
source.
• Depress the tabs (28) and remove the
HDL cassette (25) from the cassette
housing (12, Fig. 8) in the trimmer
head.
• Remove the used piece of line from
the cassette.
• Remove any dirt and grass from the
cassette and housing.
• Thread a new piece of line (26)
through the holes in each side of the
cassette.
• Place the metal ferrule (27) in position
as shown.
• Align the cassette tabs with the slots
(22, Fig. 8) in the housing.
• Push the cassette onto the housing
until it snaps securely into place.
8
TROUBLESHOOTING
If your tool does not seem to operate
properly, follow the instructions below. If
this does not solve the problem, please
contact your nearest Sears Parts & Repair
Center.
WARNING: To avoid serious injury,
switch off and unplug the tool before
performing any maintenance.
Tool runs slowly
• Check that the cassette housing (12)
can rotate freely. Carefully clean it if
necessary.
• Check that the cutting line does not
protrude more than 4-3/8 in. from the
cassette. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
• Keep the tabs depressed and remove
the cassette from the cassette housing
in the trimmer head.
• Pull the cutting line until it protrudes
4-3/8 in. from the cassette. If
insufficient cutting line is left on the
spool, install a new spool of cutting
line.
• Align the tabs on the cassette with the
cut outs in the housing.
• Push the cassette onto the housing
until it snaps securely into place.
• If the cutting line protrudes beyond the
trimming blade, cut it off so that it just
reaches the blade.
If the automatic line feed still does not
work or the spool is jammed, try the
following suggestions:
• Carefully clean the cassette and
housing.
• Remove the spool and check if the
lever in the cassette can move freely.
• Remove the spool and unwind the
cutting line, then wind it on neatly
again. Replace the spool into the
cassette.
9