SFA SANICOMPACT Instructions D'installation Et D'entretien page 4

7340 NOTICE N°204 4/02/08
1
GENERAL DESCRIPTION
The SANICOMPACT is a combination of a vitreous china
®
toilet with a built in flushing, macerating and pump system.
The SANICOMPACT is comprised of two major
®
components: the china toilet body and the macerating/pump
unit in the base of the toilet.
NORMAL OPERATING CYCLE
1a
By activating an air switch on top of the toilet, an electronic
circuit and solenoid are activated in order to fill and wash
the sides of the bowl. The motor is started and the waste
and paper is sucked into the unit where it is ground up and
pumped away. The motor stops after approximately
15 seconds and the timer program refills the bowl with fresh
water.
The SANICOMPACT is a water efficient toilet, it uses
®
approximately 4 liters (1.06 gallons) of water per flush.
2
LIST OF PARTS SUPPLIED
See fig. n°2 (technical data sheet).
DIMENSIONS See fig. n°3 (technical data sheet).
3
4
PERFORMANCE CURVE
See fig. n°4 (technical data sheet).
5
INSTALLATION
LOCATION
5a
Install the SANICOMPACT
installing, leave a 1 / -inch (15mm) space between the rear
2
of the unit and the wall for installation of the discharge pipe.
DISCHARGE PIPE INSTALLATION
5b
See fig. n° 5a 1, 2, 3 (techincal data sheet).
At the rear of the SANICOMPACT
1 / -inch in diameter. Enclosed with the SANICOMPACT
1
4
is a rubber elbow and a flapper style checkvalve
I
assembly
checkvalve into the
rubber hose, know in which direction you want to run the
discharge installation. When facing the toilet from the front,
you may want to run the discharge pipe to either the right
hand side or to the left hand side of the SANICOMPACT
It is very important, that the open side of the checkvalve
flapper, faces the direction of the discharge pipe.
Insert flapper assembly into the pipe and push discharge elbow
over it. Tighten the assembly with the provided gear clamp.
1. PVC: 1-inch solvent welded pipe. The flared end of a
1-inch coupling (or bend) fits exactly inside the rubber
elbow. This pipe has a thicker wall thickness and fits
therefore inside the discharge elbow. Use bends rather
than elbows. Use two 45 ° elbows back-to-back to make
up a 90° elbow.
2. Copper: 1-inch copper.
3. The flared end of a 1-inch coupling (or bend) fits exactly
inside the rubber elbow. Use bends rather than elbows.
4. CPVC: 1-inch solvent weld pipe.
5. The flared end of a 1-inch coupling (or bend) fits exactly
inside the rubber elbow. Use bends rather than elbows.
Use two 45° elbows back-to-back to make up a 90 ° elbow.
If you make the discharge installation with pipe smaller than
1 / -inch, start the installation by inserting a coupling or an
1
4
elbow into the discharge elbow and clamp down with a gear
clamp. From there use a short piece of pipe before you
change directions, (up, down, rear).
Do not yet connect the short piece of pipe to the discharge
installation. If your installation requires a vertical discharge
(and when made with 1-inch material), you may want to
install a Full-Flow Ball Valve for servicing purposes and
9:19 Page 4
at a convenient location. When
®
is a rubber hose of
®
. Before inserting the
H
finish your discharge pipe installation.
The connection to the soil-stack should be made with an
approved TY fitting and should be in accordance with your
local plumbing code. (Using a SADDLE CLIP may not be
permitted in your area.)
Because of the incorporated non-return valve, the pipe work
can be installed up to 3m (9 feet) in height. (It is unadvisable
to add an additional check valve.) It is possible to install the
discharge pipe in either upwards or downwards direction.
When discharging downwards it is necessary to run the
discharge pipe horizontally for a distance of 12-inches
(30cm) before changing directions.
Normally, an anti-siphon valve is not necessary because
the SANICOMPACT
®
HAND BASIN DISCHARGE PIPE WORK INSTALLATION
5c
See fig. n°5b 1, 2, 3 (technical data sheet).
To install the discharge hose, lay the SANICOMPACT
its side. Cut the nipple at the base of the motor unit.
Debur the cut and connect the flexible input pipe that allows the
hand basin to be connected. Handbasin must be located on the
same floor than the macerating system.
WATER SUPPLY CONNECTION
5d
See fig. n° 5c (technical data sheet).
For the best possible flushing action, the SANICOMPACT
needs to be connected to a
is supplied with a supply tube. The
SANICOMPACT ®
copper end of this supply tube will fit inside the
compression end of a shut-off valve. Due to the international
distribution of our product range, it may be possible that the
tip of the supply connector is metric. Simply cut this portion
off and you are left with a
®
ELECTRICAL CONNECTION
5e
The SANICOMPACT
60 Hz, 15 Amp. Ground Fault Circuit Interrupter, (either of
the breaker or receptacle type).
Connect only to receptacle protected by a ground fault
circuit.
Warning: risk of electric shock - this pump is suplied with a
.
®
grounding conductor and grounding type attachment plug to
reduce the risk of electrical shock be certain that it is
connected only to a properly grounded - type receptacle.
Note: Do not connect the SANICOMPACT
source supplied by an inverter.
INSTALLATION OF FLOOR FASTENERS
5f
See fig. n° 5d (technical data sheet).
After installing the water supply and discharge pipe, place the
in such a manner that it lines up with the
SANICOMPACT ®
piping. Mark the perimeter of the base with a pencil on the
floor. Mark the mounting holes of the bowl on the floor .
Remove the unit. Measure from the intersection of the
mounting holes / -inch (1cm) inward, this mark will be the
3
8
back of the plastic bracket which rests eventually against
the inside of the china bowl. Mark and drill holes. If
installed on a concrete or stone floor , drill two
(8mm) holes approximately 2-inch (50mm) deep and insert
plugs. If installed on a wooden floor , drill a pilot hole for
number 10 wood screws. Do not over tighten the screws as
the porcelain base may crack.
COMMISSIONING THE UNIT
5g
1. Open the stop valve completely.
2. Plug the electrical cord into the receptacle.
3. Push the air switch and hold for one second, let the unit
go through its cycle, repeat.
4. Now throw some toilet paper into the bowl and press the
automatically stops siphoning action.
/ -inch water supply. The
1
2
/
3
8
/ " connector.
3
8
should be connected to a 120 V,
®
to a power
®
5 /
16
on
®
®
-inch
-inch