Metro makro GRV1100 Mode D'emploi page 16

35. D o not place heavy objects or objects filled
with water, e.g. vases, on the appliance.
36. K eep a minimum distance of 10cm between
all sides of the appliance and walls or other
objects. If the distance is too small, the cooling
capacity may be impacted.
37. A fter turning the appliance off, always wait
at least 5 minutes until turning it on again.
Otherwise, the compressor may be damaged.
38. T he appliance is very heavy. It is
recommended to roll it for transport whenever
possible. If the appliance must be lifted,
please only do so with several people or with
machines intended for this purpose. The
appliance must only be lifted from the exterior
of the base to avoid damage. Do not move
the appliance by application of pressure to the
surface. Never tilt the appliance more than
45° or turn the appliance on its side or upside
down to avoid damaging the refrigerant circuit.
The above applies to the packed as well as
the unpacked appliance.
39. D o not apply excessive pressure to the glass
to prevent it from breaking.
40. I mportant! Allow the appliance to stand
upright for at least 2 hours before connecting
it to a mains outlet for the first time, so that the
refrigerant can settle. The same applies if the
appliance is moved at a later date.
41. D o not use aerosol cans near the appliance.
42. D o not use the appliance in explosive
atmospheres given through a combustible
mixture of air and flammable fumes, vapours,
mist or dust.
43. T he recommended setting temperature for
optimum food preservation is 1-10°C.
44. B e aware that temperature affects the taste of
food.
Electrical safety
1. Ensure the rated voltage shown on the rating
label corresponds with the voltage of the
power supply.
2. Do not operate any appliance with a damaged
power cord or plug, when the appliance
malfunctions or has been damaged in any
manner.
3. Protect the power cord against damages.
Do not let it hang over sharp edges, do not
squeeze or bend it. Do not place the appliance
on the power cord. Keep the power cord away
from hot surfaces and ensure that nobody can
trip over it.
4. Do not open the housing under any
circumstances. Do not insert fingers or foreign
objects in any opening of the appliance and do
not obstruct the air vents.
5. Protect the appliance against heat. Do not
place close to heat sources such as stoves or
heating appliances.
3. Operation
Placement
• Place the appliance on a stable and level surface.
• Ensure the appliance is properly levelled using a water spirit level. Use
furniture levelling wedges, if you detect the appliance is not levelled or
wobbling.
• Let the appliance rest in its intended position for a minimum of 2 hours
before operating to prevent damages to the cooling circuit through shaken
refrigerant.
Switching the appliance on/off
• The appliance is switched on once connected to the power supply.
Unplug to switch off.
• The appliance will emit an audible signal when connected to the power
supply.
• Wait at least 5 minutes before plug in the appliance again after
unplugging or a power break.
• We recommend unplugging the appliance when not in use.
Operating panel
Button Function
press to switch the light on or off
press and hold (> 6 seconds) to switch the
(manual) defrosting on or off
press to set the cooling temperature afterwards with the
buttons
press again to exit the temperature setting
press to increase the cooling temperature
press to decrease the cooling temperature
Indicator Function
displays the numeric value of the compartment / cooling
temperature
a dot will appear on the display below the following symbols to
indicate their current state
on
off
flashing
on
off
flashing
Notes:
• Pressing the SET button enters the temperature setting and the display
changes from compartment to cooling temperature. Pressing the SET
button again exits the temperature setting and the display changes from
cooling to compartment temperature.
• 10 seconds without input exits the temperature setting.
• Every press of a button is confirmed with an audible signal.
• The actual temperature of food or beverages may vary from the
compartment temperature for a while.
Setting the temperature
1. Press the SET button to enter the temperature setting. The display will
show the current setting.
7
and
cooling active
cooling inactive
preparing cooling process
defrosting active
defrosting inactive
skipped scheduled defrosting
GB