Table des Matières
Publicité
Installation manual e-MatriX linear 1050-1300/400 I,II,III
Assemble the flex. waterpipe
Press the blue flex. pipes 15mm in a coupling
piece. When mounting correctly, you feel re-
sistance that you have to push through.
Check the connection by pulling the pipe. Secure
the connection with the supplied red / or blue
safety clips.
➢ Please note !
A watertight connection is only guaranteed with
safety clips.
Disassemble the flex. waterpipe
Remove the red or blue safety clip
Push the pipe in, hold the flange and pull the pipe
out of the coupling.
This appliance is equipped with the following over-
flow protection:
Electromechanical valve in the Control box which is
controlled by a
overflow sensor in the water tank.
Absorption valve in the Engine that operates when
water unexpectedly flows from the reservoir. See
fig. 5.0-K.This appliance is equipped with the fol-
lowing (overflow) protections:
•
Electromechanical valve in the Control
box that is controlled by sensors in the
water tank.
•
Absorption valve in the Engine that kicks
in when the water sump has an unexpect-
edly overflow, see fig. 5.0-K.
4.5
LED lighting (optional)
LED floor lighting
The bottom lighting, which is located in the bottom
plate, can be switched on and off with both the re-
mote control, see fig. 6.0 and the App. (See user
manual). See fig. 3.0-F and 4.0 for the position of
the connection of the bottom lighting.
LED top lighting
The top lighting can be switched on and off with
both the remote control and the app. (See user
manual).
See fig. 3.0-E and 4.0 for the position of the con-
nection of the top lighting.
4.6 Removing the bottom plate with LED lighting
(see fig. 4.0)
➢ Please note !
To prevent damage / scratches, it is strongly rec-
ommended to protect the moldings. See fig. 4.0-
A. Should scratches nevertheless occur, this can
40 <
<
<
<
only be repaired with spray paint. Order number:
09000026.
• Remove the decoration set;
• Lift the bottom plate in the middle and rest it
carefully in front of the fire. See fig. 4.0.
• Loosen the plug connection, for this press the re-
taining clip of the plug. Now remove the bottom
plate.
Install LED floor lighting
• Lift the bottom plate in the middle and rest it
carefully in front of the fire. See fig. 4.0.
Insert the plug into the correct connector of the
terminal block (see fig. 3.0-F and 4.0), carefully
place the bottom plate. (Check that the cable is not
in the fire hole).
4.6
Test mode
Do a performance test. See chapter 7 and check all
water connections for leaks,
before installing the decoration set and the front
glass.
Functional test via the ITC-V2 app:
(only possible in dealer setting)
Make sure the ITC-V2 app is connected to the fire.
Navigate to Menu / Diagnosis / Test mode.
See fig. 7.0a to 7.0d.
On this screen all individual components can be
tested for function.
All components are also checked by a self-test in
the normal starting procedure.
Any error messages are displayed in the App.
Click on the "exclamation mark" symbol at the top
left of the screen for additional information about
the notification.
4.7
Build-in structure and ventilation
requerments
•
The construction may not rest on the fire.
•
Take into account the thickness of any fin-
ishing layer!
•
Keep a minimum distance of 10mm be-
tween build-in frame and false chimney
breast when using combustible material,
see fig. 1.4.
•
Take into account a minimum distance of
2mm due to expansion of the fireplace,
see fig. 1.4.
Publicité
Table des Matières
