Start-Up; Mains Connection; Dust / Chip Exhaustion; Working Instructions - ATIKA ADH 204 Notice Originale

Start-up

Mains connection

Compare the voltage listed on the machine
230 V, with the mains voltage and connect the machine to a
suited and and properly earthed electrical socket.

Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and 10 A inert fuses.
 Use connection cable or extension cable respectively with a
cross section of at least 1,5 mm².
On / Off Switch E
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Switch on
Fold up the yellow hinged cover.
 If the hinged cover is locked into place, you have to
push the red knob in arrow direction at first.
Press the green button ( I ) on the switch.
If there is a power cut, the machine switches off
automatically. Push the green ( I ) button to start the
machine again.
Switching off
Press the red button on the hinged cover.
Motor protection
 The motor is equipped with a safety switch and switches
off automatically when overloaded.
It can be switched back on following a cooling off phase
–
(5 10 min).
Press the
1. red button ( 0 ).
2. the small button next to the button (8)
3. the green button ( I ) to start

Dust / chip exhaustion

The wood dust generated during operation impedes the
necessary view and is harmful to health to some
degree.
Connect therefore always a chip exhaust system or small
vacuum cleaner with suitable adapter to the chip exhaust neck
(31) (Ø 100 mm).
Make sure that the shavings extractor is properly
earthed.

Velocity of air on the extractor connector on the machine
≥
20 m/sec.

The motor will only start if the extractor hood (29) is
properly attached and thus releases the safety switch.

Working instructions

s type plate, e.g.
'
 Workplace tidied?
 Is the surface planing and thicknessing machine securely
 Are all fastening screws tightened?
 Is the blade securely fastened on the blade shaft?
 Are the cutting blades sharp and undamaged?
 Does the backstroke protection work?
 Are the pushing bars handy?
 You may not start to operate the machine until you have
 When machining make sure that the unused blade shaft is
 Place yourself outside of the area of danger.
 Place your hands flat on the workpiece with fingers closed.
 Never remove loose splinters, chips, or similar by hand.
 Connect a dust or shavings extractor.
 Make sure that the feed rollers and cutting tools are free
 Do only machine workpieces the dimensions of which are
 Use a workpiece support (e.g. roll stand / table) for long
 Do not guide back the workpiece over the open-running
 Adjust the smallest cutting depth after your work is finished.
"Intended use" and "Safe working manners".
Surface planing
The objective of surface planing is to smooth a rough surface
(planing), e.g. to smooth the edge of a board.
For this the workpiece is placed onto the feed table plate and is
machined on its underside. Feed direction is from right to left.
Preparations
1. Place the crank handle (15) onto the shaft end on the table
Before starting to work consider the following safety
advices to keep the risk of injuries as small as
possible.
installed?
read these operating instructions, observed all the
instructions given and installed the machine as described!
Also, note the following important points:
covered by the knife guard.
from wood shavings and dust.
within the specifications for this machine (see
"
data ).
workpieces. The workpiece support is correctly adjusted
when the table plate and the workpiece support are at the
same height.
blade shaft.
At any rate, follow all instructions in the sections
Pull the mains plug before performing
settings.
Installing the dust extractor
plate and turn it anticlockwisely to bring the thicknessing
table plate to its lowest position.
"
Technical
L
F F
20