Electrical Safety; Assembly; Preparing For Startup - ATIKA ADH 204 Notice Originale

 Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and
adjusting tools are removed.
 Store unused equipment in a dry, locked place out of the
reach of children.

Electrical safety

 Extension cable to be designed in compliance with IEC 60
245 (H 07 RN-F) having a core cross-section of at least:
− 1.5 mm² for cable lengths up to 25 m
− 2.5 mm² for cable lengths over 25m
 Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
 Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
 Protect yourself against an electric shock. Avoid touching
earthed parts with your body.
 The connector of the connection cable must be splash-proof.
 Wind off completely the cable when using a cable drum.
 Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
 Regularly check the saw cable and if damaged, have it
renewed by a recognised skilled electrician.
 When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
 Regularly check the extension cables and replace them if
they are damaged.
 Do not use any defective connection cables.
 Do not set up any provisional electrical connections.
 Never bypass protective devices or deactivate them.
 Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points.
Local regulations
measures must be observed.
–
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer service
points.
Use only original spare parts and accessorie parts.
Accidents can arise for the user through the use of
other spare parts. The manufacturer is not liable for
any damage or injury resulting from such action.
19
especially regarding protective
–

Assembly

You have to attach the following parts:
Rubber feet (7) A
Guide plate (1) B
 Attach the guide plate (1) to the table location provided for
this.
 Secure the guide plate using two washers A 6.4 and two
screws M6x25.
Blade shaft guard (14)
 Attach the complete blade shaft guard (14) to the table
location provided for this.
 Secure the blade shaft guard using the star grip screw (11).
Securing on the workbench
Drill four holes into your workbench as shown in the picture.
Secure the surface planing and thicknessing machine onto the
workbench using 4 screws (M8). You can also secure the
surface planing and thicknessing machine onto a work plate. In
this case the plate must be safely secured onto the workbench.

Preparing for startup

 To achieve flawless functioning of the machine, please
follow the instructions listed:
 Place the surface planing and thicknessing machine at a
location which meets following conditions:
secured against slipping
−
free of vibrations
−
− even
− free of tripping hazards
− adequate light
 Before each use, check
− connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
− the flawless condition of pushing bar and pushing block
− faultless function of the blade shaft guard (12)
− that the unused blade shaft is covered by the blade shaft
guard
− the proper condition of cutting blades
− the faultless function of the backstroke protection (41)
the proper condition of the transport rollers
−
Checking the function of the blade shaft guard (12)
Loosen the locking screw (16) and check whether the blade
shaft guard can be freely moved.
Checking the function of the backstroke protection (41)
Check first whether all grippers:
− return to their starting position on their own
− are tapered
Place a workpiece on the thicknesser table plate (18) and push
it all the way beneath the grippers. Adjust the height of the table
so that the transport rollers touch the workpiece. Now pull the
workpiece towards you. The grippers must block preventing you
from pulling out the workpiece.
C
D
L
F