General Information; Technical Data; Accessories For Assembly; Central Assembly With Welding - Beninca ZED.RIE Mode D'emploi

1) GENERAL INFORMATION

ZED is an automation for overhead doors with counterweights, for central or side assembly. Compact and linear, the ZED gear motor adapts to any type
of overhead door. As well as guaranteeing maximum reliability, ZED offers a continuous, regular and silent movement. It is easy to fit using screws or
welding. The gear motor is irreversible which ensures that the door can be closed without the use of electric locks. In the event of a power cut the door
may be released by simply turning a knob on the gear motor.
For good operation of this automation, the overhead door must possess the following characteristics:
- good robustness and rigidity
- good balancing
- good sliding of the guides.
In any case, it must be possible to perform manual opening and closing with ease.

2) TECHNICAL DATA

Power supply
Consumption
Power
Torque
Jogging
Operating time
IP Class
Operating temperature
Capacitor
Noise level
Lubrification
Weight
Control unit supply
Output supply
Power maximum motor
Output supply accessories
Radio receiver
Rolling code transmitters supported
* IP44 version available

3) ACCESSORIES FOR ASSEMBLY

3.1) CENTRAL ASSEMBLY WITH WELDING

• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000 mm);
• pair of galvanized tubes with bush AU.45Z (1500 mm) or AU.45ZL (2000 mm);
• pair of galvanized straight arms AU2.D. If there is no space, use the pair of galvanized bent arms AU2.C (see Fig. 7).

3.2) CENTRAL ASSEMBLY WITHOUT WELDING

• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000 mm);
• pair of galvanized tubes with bush AU.45Z (1500 mm) or AU.45ZL (2000 mm);
• pair of straight arms with bush AU2.DNS (600 mm).

3.3) LATERAL ASSEMBLY WITH WELDING

• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000 mm);
• splined bush AU.45B; if the geared motor is too far from the edge of the door, use the pair of tubes with welded bush AU2.45T (150 mm);
• pair of galvanized straight arms AU2.D. If there is no space, use the pair of galvanized bent arms AU2.C (see Fig. 7).

3.4) LATERAL ASSEMBLY WITHOUT WELDING

• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000 mm);
• pair of straight arms with welded bush AU2.D45 (600 mm) or AU2.D45L (2000 mm); if the geared motor is too far from the edge of the door, use the
pair of tubes with welded bush AU2.45T (150 mm) with the pair of straight arms with bush AU2.DNS (600 mm).

4) ADDITIONAL ACCESSORIES

- External release with customized key ZED.E.
- Release from inside/outside by means of a handle with customized key ZED.SE.
- ZED.MS wire release.
ZEDL.RIE
230Vac (50Hz)
1,4 A
320 W
330 Nm
30%
≈22s
IP40*
-20°C/+50°C
10μF
<70 dB
GREASE
10 Kg
230 Vac 50/60 Hz or 115Vac 50/60Hz according to the version
1 or 2 motor 230 Vac
300+300 W
24Vac 1A max.
built in 433,92 MHz (Advanced Rolling Code ARC)
64
ZED.RIE
1,5 A
340 W
350Nm
≈14s
21
EN