General Information; General Characteristics - Beninca ZED Mode D'emploi

Manufacturer: Automatismi Benincà SpA.
Address: Via Capitello, 45 - 36066 Sandrigo (VI) - Italia
We herewith declare that: the operator for overhead doors model ZED.
• is intended to be incorporated into a machine or assembled together with other devices to form a machine in compliance with the
EC Directive 98/37, as amended;
• therefore, is not in every respect complying with this Directive;
• is complying with provisions set forth by the following other EC Directive:
EC Low voltage Directive (73/23/EEC, 93/68/EEC).
EC Directive of Electromagnetic Compatibility (89/336/EEC, 93/68/EEC)
Moreover, we herewith declare that the system shall not be put into service until the machine in which the same will be incorporated
or of which it will become a component, is acknowledged compliant with the EC Directive 98/37 and applicable national legislation
and a related declaration of conformity is drawn up. In other words, no servicing shall be carried out until the system under this
declaration does not form one single final machine with other components.
Benincà Luigi, Legal responsible.
Sandrigo, 08/04/2008.
IntrOduCtIOn
We congratulate you for choosing the ZED gear motor. All the
items in the vast Benincà range are the fruit of twenty years of ex-
perience in the sector of automatisms and of a continuous search
for new materials and state-of-the-art technologies. For this very
reason, today we are able to offer extremely reliable products
which, thanks to their power, efficiency and long life, fully satisfy
the demands of the end user. All our products are made in con-
formity with the regulations in force and are covered by guarantee.
Moreover, a TPL policy stipulated with a leading insurance com-
pany covers any damage to persons or things caused by manu-
facturing defects.

1. generaL InfOrmatIOn

For good operation of this automation, the overhead door must
possess the following characteristics:
- good robustness and rigidity
- good balancing
- good sliding of the guides.
In any case, it must be possible to perform manual opening and
closing with ease.

2. generaL CharaCterIstICs

ZED is an automation for overhead doors with counterweights, for
central or side assembly. Compact and linear, the ZED gear mo-
tor adapts to any type of overhead door. As well as guaranteeing
maximum reliability, ZED offers a continuous, regular and silent
movement. It is easy to fit using screws or welding. The gear motor
is irreversible which ensures that the door can be closed without
the use of electric locks. In the event of a power cut the door may
be released by simply turning a knob on the gear motor.
3. aCCessOrIes fOr assembLy
Central assembly with welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• pair of galvanized tubes with bush AU.45Z (1500 mm) or AU.45ZL
(2000 mm);
• pair of galvanized straight arms AU2.D. If there is no space, use
the pair of galvanized bent arms AU2.C (see Fig. 6).
14
EC Declaration of Conformity regarding machines
(Directive 98/37 CE, Annex II B) - No servicing
Central assembly with welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• pair of galvanized tubes with bush AU.45Z (1500 mm) or AU.45ZL
(2000 mm);
• pair of straight arms with bush AU2.DNS (600 mm).
Central assembly with welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• splined bush AU.45B; if the geared motor is too far from the edge
of the door, use the pair of tubes with welded bush AU2.45T (150
mm);
• pair of galvanized straight arms AU2.D. If there is no space, use
the pair of galvanized bent arms AU2.C (see Fig. 6).
Lateral assembly without welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000 mm);
• pair of straight arms with welded bush AU2.D45 (600 mm) or
AU2.D45L (2000 mm); if the geared motor is too far from the edge
of the door, use the pair of tubes with welded bush AU2.45T (150
mm) with the pair of straight arms with bush AU2.DNS (600 mm).
4. addItIOnaL aCCessOrIes
- External release with customized key ZED.E.
- Release from inside/outside by means of a handle with custom-
ized key ZED.SE.
- ZED.MS wire release.
5. InstaLLIng the autOmatIsm
The automation with only one motor and central assembly is rec-
ommended for overhead doors with an area less than or equal to
12 m2; for larger dimensions or for overhead doors with a built-in
small door use 2 side motors.
1) After identifying the axis of rotation of the overhead door A,
determine the axis R passing through the bottom at a distance of
100 mm (fig. 1); this is the axis of the splined shaft that comes out
of the gear motor.
Then anchor the plate of the gear motor to the door following the
indications in figs. 2 and 3.