Martin Yale intimus 45SC2 Instructions D'opération page 6

GB
CONTROLS:
7 = Control display (Fig. 1)
"Oil cutters"
Comes on when the cutters in the cross
cut version must be oiled. The lubrication
procedure must be acknowledged on
the reverse button (4) (see description in
"CUTTER MAINTENANCE").
8 = Control display (Fig. 1)
"Door open"/ "Door malfunction"
a) "Door open"
Comes on if the door on the lower part
of the machine is opened. The machine
switches off automatically and cannot
be started as long as the door remains
open.
b) "Electrical fault"
Flashes when there is an electrical fault
in the door sensor. The machine switches
off. Please contact your dealer.
9 = Control display (Fig. 1)
"Motor overload" /
"Electrical fault"
To find out what to do see the relevant
description under the "MALFUNCTION"
section.
a) "Motor protection"
Comes on when the motor has been
overloaded and has switched off. The
machine cannot be started while the
motor is cooling down.
b) "Electrical fault"
Flashes when there is an electrical fault
inside the control board. At the same
time the function button (2) LED display
flashes. The machine switches off.
Please contact your dealer.
10 = Control display
"Receptacle full" (Fig. 1)
Comes on when the receptacle is full and
needs to be emptied. At the same time the
machine switches off automatically.
11 = Paper feed slot (Fig. 3)
12 = Receptacle (Fig. 4)
13 = Oil reservoir (Fig. 4)
6
7
8
2
fig. 1
OPERATION
The shredder may not be used as a
step ladder or as a seat. Danger of
falling due to breakage!
SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to
"Ready":
- Press the function button (2) briefly.
- The function button (2) LED display
on for "Ready".
- The machine can be loaded.
MATERIAL FEED:
Feed paper into the cutting mechanism through
the paper feed slot (11) (fig. 3).
The machine automatically switches to forwards
running, draws the material in and automatically
switches off after shredding.
Note: For shredding transparent films, the
machine must be manually switched to forwards
running (press and hold the forwards button (3)
for approx. 2 secs.).
By briefly pressing the function button (2) (Stop
function), the shredding process can be stopped
at any time. To continue, press and hold the
forwards button (3) for approx. 2 secs.
If the machine is not used for a period of approx.
5 mins., it automatically switches off.
Never feed the shredder with a
quantity of material exceeding the
maximum indicated.
TECHNICAL DATA section!
Should the
overloaded, follow the instructions under
"MATERIAL JAM IN MACHINE" under
"MALFUNCTIONS".
3
9
10
11
4
fig. 3
EMPTYING THE RECEPTACLE (Fig. 4):
If the receptacle is full the machine switches off.
The control display
as follows:
- Open the door. The control display
comes on. If there is still material in one of
the feed slots, the control display
comes on.
- Pull out the receptacle (12) from the lower part
comes
of the housing and empty the contents. The
control display
- Slide the emptied receptacle (12) back into the
lower part of the housing and close the door.
The control display
- If the control display
the forward button (3) briefly. The remaining
material in the feed slot is shredded and the
display go out.
Note: The machine will only run if the door is
closed.
DYNAMIC LOAD DISPLAY:
To prevent a material jam and thus ensure a
continual, effective destruction of the data
carriers, the current load level of the motor is
displayed during the shredding process by a
coloured, diffuse light in the feed slot as follows:
Green light:
Yellow light:
Red light:
Refer to the
machine become
5
6
(10) comes on. Proceed
(8)
(6) also
(11) goes out.
(8) goes out.
(6) comes on, press
load < 50%
load 50 - 75%
load 75 - 100%
13 12
fig. 4