Reference Standards And Laws; Unpacking; Positioning; Connections - Mareno SDSM6E Instructions Pour L'installation, Emploi Et Entretien

(41°F) and + 35°C (95°F) and in any case in an environment
that does not cause any malfunction of the device.
• Important! This appliance must not be positioned above any
heat-producing appliance.

4 REFERENCE STANDARDS AND LAWS

Install the appliance in compliance with current regulations.

5 UNPACKING

Check the state of the packaging and in the event of damage,
ask the delivery person to inspect the goods.
• Remove the packaging.
• Remove the protective film from the exterior and interior pa-
nels. Use a suitable solvent to remove any residual adhesive
from the panels.

6 POSITIONING

• The overall dimensions of the appliance and the position of
connections are given on the installation diagram at the start
of this manual.
• The appliance can be installed independently.
• Position the appliance at least 25 cm from adjacent walls.
This distance can be reduced in the presence of non-combu-
stible walls or heat-insulated walls.
• The appliance is not suitable for flush mounting.
• The appliance must be placed on a dry, smooth, strong, sta-
ble and even surface of a sufficient width, at least 55 cm from
the ground.

7 CONNECTIONS

The position and dimensions of connections are given in the
installation diagram at the start of this manual.
7.1 ELECTRICAL CONNECTIONS
Check that the appliance is designed to operate at the voltage
and frequency of the power supply present on site. Check the
details given on the appliance data plate.
If used, the symbol indicates:
CAUTION - HAZARDOUS VOLTAGE.
• Install an adequately rated omnipolar circuit-breaker upline
of the appliance in an easily accessible point, in compliance
with installation regulations; the circuit breaker must guaran-
tee immediate omnipolar disconnection from the mains, with
a minimum contact opening that allows complete disconnec-
tion in overvoltage category III conditions. The maximum per-
mitted current dispersion is 1mA/kW.
• For electrical connection, use a rubber-sheathed flexible ca-
ble which is oil resistant, type H05RN-F or H07RN-F, for ca-
ble size consult the technical data table.
• Connect the power supply cable to the terminal board as
shown in the wiring diagram supplied with the appliance.
• Secure the power supply cable with the cable clamp.
• Protect the power supply cable on the outside of the applian-
ce with a rigid plastic or metal pipe.
• If the power supply cable is damaged, it must be replaced
by the manufacturer or the technical after-sales service or,
in any case, by a suitably qualified technician, so as to avoid
any risk whatsoever.
4
7.2 PROTECTIVE EARTH AND EARTH BONDING CON-
NECTIONS
Connect the appliance to an efficient ground circuit. Connect
the earth conductor to the terminal with the symbol
ted next to the main terminal board.
Connect the metal structure of the appliance to the equipoten-
tial node. Connect the conductor to the terminal with the symbol
on the outside part of the bottom.
• This symbol indicates that the appliance must be included in
an equipotential system connected in compliance with cur-
rent regulations.

8 COMMISSIONING

See Chapter " INSTRUCTIONS FOR MAINTENANCE".

INSTRUCTIONS FOR USE

REMINDERS FOR THE USER

The manufacturer will not be liable for
any damage or injury resulting from fai-
lure to observe the following rules.
• Read this manual carefully. It provides im-
portant information for safe installation,
use and maintenance of the appliance.
• Keep this manual in a safe place known to
all users so that it can be consulted throu-
ghout the working life of the appliance.
• Appliance installation and maintenance
must be carried out by qualified techni-
cians authorized by the manufacturer, in
compliance with current safety standards
and the instructions in this manual.
• For after-sales service, contact technical
assistance centers authorized by the ma-
nufacturer and demand the use of original
spare parts.
• Have the appliance serviced at least twice
a year. The manufacturer recommends ta-
king out a service contract.
• The appliance is designed for professional
use and must be operated by trained per-
sonnel.
• The appliance is to be used for cooking
food as specified in the reminders for use.
Any other use will be considered improper.
• Avoid operating the appliance when emp-
ty.
• Do not leave the appliance unattended
while in operation.
loca-