Publicité
Les langues disponibles
Les langues disponibles
GB
CLEANING THE PHOTOCELLS (8) (Fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through the
feed slot, or switch the machine to reverse and wipe
both „eyes" of the photocell with a brush.
TAKING OUT EXCESS PAPER
IN CASE OF OVERLOAD:
If the shredder has stopped due to an overload
(motor protection) take the excess paper out of the
inlet as follows:
1. Depress the reverse pushbutton (4) (fig. 2). The
material is released.
2. Lift up the hopper. The pilot lamp „door open" or
„hopper open" (7) (fig. 2) will light.
3. Remove the excess material by hand from the inlet
guide.
Note: In this case, there is no danger of injury as all
circuits are interrupted when the hopper is lifted
and the machine cannot be started.
MOTOR FAULT:
The machine is equipped with a thermally protected
motor. Should this motor be overloaded, it will switch
off automatically. In such case the pilot lamp „ready"
(5) (fig. 2) flashes. Additional the pilot lamp of the
control display (7) (fig. 2) lights up.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can restart
the machine and continue shredding.
Description
Plastic bag, 600 x 380 x 1100 x 0,6 mm
Lubrication bottle, 125 ml
Note: For orders of special accessories and spare parts, please contact your dealer.
MAINTENANCE
MALFUNCTION
FAULT CHECKLIST:
If the machine is not functioning properly, you should
check the following:
- is the plug conneted to the mains?
- is the mains switch (1) turned on?
- is the door closed?
- is the hopper cover closed?
- is the collecting bag full?
The bag has to be emptied.
- is the motor overloaded?
Please refer to the section headed „Motor Fault".
- is there a phase failure?
Check the three-phase fuse at the power supply
socket, and replace if necessary.
If you still cannot isolate the fault or other faults
are statable, the machine shouldn't be operated.
Please report to / notify our customer service
department.
ACCESSORIES
8
fig. 4
Order-No.
80946
99943
7
H200CP4 (852CC)
CUTTING SYSTEM MAINTANANCE:
After about 2 hours of continuous opera-
tion run the cutting system in reverse for
about 30 seconds and, at the same time,
spray some of the enclosed special oil onto
the cutting system.
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(mains switch (1) (fig. 1) switched to „0").
DISPOSING
DISPOSING OF THE MACHINE:
Dispose
of
the
machine
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine or
its packaging with household trash.
TECHNICAL DATA
Cutting width:
3.8x40 (cross-cut)
Cutting capacity:
70-80 sheets (70 g/m
in two stacks
Working width:
444 mm
Power:
3.9 kW
Supply voltage:
400V/50Hz
230V/50Hz
415V/50Hz
220V/60Hz
200V/50Hz
200V/60Hz
Pre-fusing:
(gl fuse, type 1 assignment)
400V-415V/50Hz:
16 A
220V-230V/50-60Hz:
25 A
200V/50-60Hz:
25 A
Width:
750 mm
Depht:
550 mm
Height:
1600 mm
Noise level:
approx. 75 dB(A)
Weight:
approx. 201 kg
in
an
)
2
Publicité
