Publicité
Les langues disponibles
Les langues disponibles
GB
OPERATING FUNCTIONS (Figs. 1, 2 and 4):
1 = Mains switch (Emergency-stop) (fig. 1)
This switch turns the machine either on (position
„1") or off (position „0").
2 = „Cutting system forward"
pushbutton (fig. 2)
Pressing this button starts the cutting system.
Material can now be fed to the shredder.
Note: Press and hold button for approx. 1 sec.
3 = „Cutting system stop"
pushbutton (fig. 2)
Pressing this button switches the shredder off,
thereby halting the cutting system.
4 = „Cutting system reverse"
pushbutton (fig. 2)
Pressing this button starts the cutting system in
reverse.
Note: Press and hold button for approx. 1 sec.
5 = Pilot lamp (fig. 2)
a) „ready"
Continously lights when the mains switch
(1) is operated.
b) „motor protection"
Flashes when the motor is overloaded. The
machine cannot be started during the cooling
down phase of the motor. Additional the pilot
lamp of the control display (7) (fig. 2) lights
up.
6 = Pilot lamp „paper jam" (fig. 2)
Lights when too much paper is fed to the cutters
(see description „AUTOMATIC RESPONSE IN
CASE OF OVER-LOADING").
7 = Pilot lamp (fig. 2)
a) „door open"/„hopper open"
Lights when the door is not closed or when the
hopper is open. The machine then switches
off automatically and it cannot be started
as long as the door is open or the hopper is
open.
Note: To turn the machine into the „Ready"-
mode again after an interruption, there
must be operated both end switches at the
corresponding turn-off device. For this the
door must be openend before not less than
10 cm or the hopper must be folded upwards
with a minimum of 10 cm.
b) „collecting bag full" (fig. 2)
Lights as soon as the collecting bag is full and
needs to be emptied. At the same time the
machine switches off automatically.
8 = Light barrier (forward operation) (fig. 4)
The shredding operation is started as soon as a
sheet of paper passes through the feed slot.
I
MAINS SWITCH
fig. 1
OPERATING THE MACHINE:
To start, switch on the unit by operating the mains
switch (1) (fig. 1). The pilot lamp marked „ready for
operation" (5), as well as the red stop-button „S" (3)
(fig. 2) will light to indicate that the machine is ready
for operation.
The paper tray may not be used as a step
ladder or as a seat. Danger of tipping over!
FEEDING CRUMPLED PAPER:
1. Open the hopper cover. The cutting system is then
automatically switched off.
Attention: The machine cannot run with open
hopper cover.
2. Fill the hopper with crumpled paper and close the
hopper cover.
Note: The crumpled paper can be dropped directly
from the wastepaper basket into the hopper of the
machine. The apportioning wings preceding the
cutting mechanism ensure more or less uniform
distribution of the paper.
Attention: The wastepaper basket is no refuse
tin and should not be emptied into the machine
thoughtlessly - in no way can the machine destroy
bottles, pens, pencil sharpeners etc.
3. Press the pushbutton switch „forward" (2) (fig. 2).
The cutting system runs and begins to shred the
paper.
Note: Do not feed any smooth paper until the
crumpled paper is completely shredded.
4. To switch the machine off press the red stop-button
(3) (fig. 2).
FEEDING SMOOTH PAPER:
- Feed smooth paper through the opening at the
lower part of the hopper to the cutting system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
Note: For manual operation, press the forward-button
(2) (fig. 2); the machine will run continously. As soon
as a sheet of paper passes through the feed slot to the
cutting system, the light barrier(8) (fig. 4) is activated
and switches the shredder off aotomatically when no
more paper is presented.
S
1
4
3
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
OPERATION
2
5
6
7
fig. 2
6
Never feed the shredder with a quantity of
paper exceeding the maximum indicated in
the technical details.
Should the machine be overfed, follow the
instructions under „AUTOMATIC RESPONSE
IN CASE OF OVERLOADING".
AUTOMATIC RESPONSE
IN CASE OF „OVERLOADING":
In case you accidentally overload the shredder, it
will automatically alleviate the problem as follows:
1. The cutting system becomes jammed. The pilot
lamp (6) (fig. 2) lights up.
2. The cutting system runs briefly in reverse, thereby
freeing the material to be shredded.
3. The cutting system automatically switches back
to forward mode.
The machine repeats this process until all the material
has been shredded satisfactorily.
EMPTYING THE COLLECTING BAG (Fig. 3):
When the collecting bag is full, the machine turns
off automatically. The pilot lamp (7) (fig. 2) lights up.
Empty the collecting bag as follows:
- Open the door and take out the sliding frame with
the collecting bag.
- Remove the rubber band, take out the full bag and
dispose of contents.
- Put the empty bag from below through the sliding
frame and put the edges of the bag approx. 10 cm
over the frame outwardly.
- Fix the collecting bag with the rubber band at the
sliding frame.
- Move back the sliding frame with the collecting
bag and close door.
Note: The machine will only run with closed door!
fig. 3
Publicité
