Publicité
Les langues disponibles
Les langues disponibles
Anleitung_NMC_355_SPK7:_
GB
while working with the cutting-off machine.
1. For your own safety, read these safety
instructions before you put the electric tool into
operation. Familiarize yourself with the toolʼs
operating range and limits, as well as the special
hazards involved in its operation.
2. Do not remove any safety devices..
3. Use personal safety equipment. Wear safety
goggles. Normal spectacles are not safety
goggles. Use a dust mask when working on
dusty jobs
4. Always remove keys and wrenches after use.
Before switching on, make sure that all keys and
wrenches have been removed from the tool.
5. Keep your work area tidy. An untidy work area
invites accidents.
6. Avoid hazardous ambient conditions. Never use
electric tools in damp or wet locations, and never
expose them to rain. Keep your work area clean.
Ensure that there is sufficient space at your
place of work.
7. Keep children away. Do not allow other persons,
particularly children, to touch the electric tool or
its cables. Keep them away from your work area.
8. Make the machine child-proof. Fit a pad-lock,
deactivate the main switch or remove the start
key.
9. Do not overload your electric tool. Electric tools
work better and safer when used within their
quoted capacity range.
10. Use the right electric tool. Do not use electric
tools to perform work for which they were not
intended.
11. Wear suitable work clothes. Do not wear loose
clothing or jewelry as they may get caught in
moving parts. Non-slip shoes are recommended.
Wear a hair net if you have long hair.
12. Secure your workpiece. Use clamps or a vise to
hold the workpiece securely. This is safer than
using your hand.
13. Take care of your electric tools. Keep mounted
attachments such as cutting-off wheels, blades
and bits sharp and clean to enable you to work
well and safely. Follow the maintenance
regulations and the instructions for changing
mounted attachments such as cutting-off wheels,
blades and bits. Check the electric toolʼs cable
regularly and have it replaced by an authorized
specialist if damaged. Check your extension
cables regularly and replace them if damaged.
Keep handles dry and free from oil and grease.
14. Always pull out the power plug. This is essential
when not using the electric tool, prior to
maintenance, and when changing mounted
attachments such as cutting-off wheels, blades
and bits.
12
24.09.2008
9:47 Uhr
Seite 12
15. Use only recommended accessories.
Recommended accessories are listed in the
directions for use. Follow the instructions issued
for the accessories. It may be dangerous to use
unsuitable accessories.
16. Do not climb on your electric tool. The tool may
topple and cause an injury.
17. Check the electric tool for damage. Each time
before re-using the electric tool, carefully check
that the safety devices or any slightly damaged
parts are working as intended. Check that the
moving parts are in good working order, that they
do not jam, and that no parts are damaged. All
parts must be correctly assembled and meet all
the conditions required to ensure that the electric
tool works correctly. Unless otherwise stated in
the operating instructions, damaged safety
devices and parts have to be repaired or
replaced by an authorized service center. Have
damaged switches replaced by a customer
service workshop. Never use an electric tool with
a switch that cannot be turned on and off.
18. Direction of operation: Make sure that the
direction arrow points toward the workpiece.
19. Never leave an electric tool unattended when it is
running. Always switch off your electric tool
before leaving it. Wait until the tool stops moving
completely.
20. Connect your electric tool to earth. An electric
tool with a PE conductor may only be connected
to a matching socket-outlet.
21. Make allowance for ambient conditions. Do not
expose electric tools to rain. Never use electric
tools in damp or wet locations. Provide good
lighting. Do not use electric tools near flammable
liquids or gases.
22. Guard against electric shock. Avoid body contact
with earthed components.
23. Keep your electric tools in a safe place. When
equipment is not being used it should be kept in
a dry, closed place out of childrenʼs reach.
24. Connect up a dust extraction system. If there are
provisions for connecting up a dust extraction
and collection system, make sure that such a
system is connected and in use.
25. Use the cable for its intended purpose only. Do
not use the cable to pull the plug out of the
socket-outlet. Protect cables from heat, oil and
sharp edges.
26. Avoid abnormal working postures. Make sure
you stand squarely and keep your balance at all
times.
27. Avoid unintentional starting. Make sure that the
switch is OFF when inserting the plug in the
socket-outlet.
28. When working outdoors, use only extension
Publicité
