SUHNER LXC 2-TOP Dossier Technique page 4

Weight
LXC 2-TOP
LXC 4-TOP
LPC 2-TOP
Air quality DIN ISO 8573-1
Max. wheel diameter
Spindle thread
(refer to spare part list)
Machine components
1 Spindle
2 Right angle gear head
3 Water connector
4 Screw
5 Wrench 2 mm
6 Safety lever throttle
7 Ring throttle
8 Exhaust Hose
9 Muffler
10 Air hose
11 Wrench 22 mm
12 Wrench 17 mm
Adaptor kit
(only for LXC 2-TOP , LXC 4-TOP)
13 Handle extension
14 Hexagon nut
15 Side handle
Recommended Accessories
16 Coupling with min ID 5.5 mm/ 7/32"
17 1/2" -Service Unit (Capacity 5-8 Micron). with wet air
include Lubricator
Suitable Tools
LXC 2-TOP / LXC 4-TOP
18 Elastic support plate with bayonet fitting 21.
19/20 Surface grinding wheels / Grinding rings / Grinding
cups / Diamond tools.
LPC 2-TOP
Backing pads with fiber discs.
Additional Abrasives and Tools can be found in the the
catalogs.
Air supply requirements
The DIN ISO quality specifications require, that air is free
of solid particles larger than 5 micron, remaining water
3
content to be max. 6 g/m
C) and air may contain 5 mg/m
observe the following:
• Operating with dirty and unlubricated air reduces tool
life substantially.
Before installing extension hoses, blow them clean and
minimize, if at all necessary coupling and keep them
4
0,93 kg
0,93 kg
0,91 kg
3/4/4
150 m
M14 or 5/8"-11
(pressure dew point +3 degree
3
of oil. Therefore please
clean.
• Rust will occur, if air supply is not lubricated and wet.
A few drops of air tool oil from time to time will prevent
rust and stops bearings from seizing.
• Conserve:
Put some drops of oil in the air inlet and briefly blow
through.
Safety Instructions
• Do not exceed max. operating speed of tool and clam-
ping element.
• Observe accurate mounting of insert tools.
• Observe mounting instructions for Mounted Stones!
• Run tool for a couple of seconds under no load,
replace vibrating insert tools at once, protect mounted
points from knocks and grease.
• Secure work, use clamps or a vise to hold work.
• The grinder operator shall wear safety goggles or face
shield at all times when the grinder is in operation.
• If noise level exceeds 85 dB(A) at the work station,
operator must use ear protection (plugs and/or ear
mufflers).
For additional safety instructions refer to enclosed bro-
chure 300006072.
Operation conditions and instructions
Valve actuation:
 Tilt safety pin towards arrow direction and
 press down lever.
Dismantling the handle:
Remove nut 14, turn extension handle 13 around, or re-
centre it.
Grinding
• Observe even material removal, avoid chattering.
• Do not treat any material containing asbestos.
Change of tools/abrasives
Disconnect air supply before changing tools/abrasives.
• Hold elastic bearing 18 with spanner 11, loosen parts
19,20 by nad or pull off.
• Check concentricity, use only vibration free tools and al-
ways observe M.OS. (Max. operating speed). Observe
mounting instructions for Mounted Stones!
Maintenance
• Store tool in a clean, dry place.
Check the idling speed from time to time.
• Even if the tool still gives satisfactory service, have it
checked by a trained mechanic after 300 to 400 opera-
tion hours, or at least once a year. Disassembly motor,
clean and replace if necessary the four vanes. Also
check/replace grease in the gear head 2.
• Warranty claims can only be considered, if tool is retur-
ned complete.