Nice MhouseKit CL2SL Instructions Et Avertissements Pour L'installation Et L'utilisation page 43

9.4.1 - Mode 1 memorisation
01. Press P1 [B] (fig. 24) for at least 3 s. When the LED P1 [A] (fig. 44)
lights up, release the key.
02. Within 10 s press any one key on the transmitter for at least 3 s to
memorise it. If the memorisation procedure is successful, the LED P1
will emit 3 flashes.
03. If there are other transmitters to be memorised repeat step 2 within the
next 10 s otherwise the memorisation phase will end automatically.
9.4.2 - Mode 2 memorisation
With Mode 2 transmitter memorisation each key can be associated with
any one of the commands shown in table 9.
In Mode 2 each key requires its own memorisation phase.
01. If the transmitter to be memorised is already memorised (this is the
case with the supplied transmitters that are already stored in mode
I) you must first delete the transmitter by performing the procedure
described in: 10.4.4 - Deleting a radio transmitter
02. Press P1 [B] (fig. 24) on the control unit, the same number of times
as your desired command, as shown in Table 9 (e.g. 3 times for the
"Open Only" command).
03. Check that LED P1 [A] (fig. 24) emits a number of quick flashes
which are equal to the selected command.
04. Within 10 s press the required key on the radio transmitter for at least
2 s to memorise it. If the memorisation procedure is successful, the
LED P1 will emit 3 slow flashes.
05. If there are other transmitters to memorise for the same command
type, repeat step 03 within another 10 seconds; otherwise, the mem-
orisation phase will stop automatically.
9.4.3 - Remote memorisation
A new radio transmitter can be memorised on the control unit without
having to use the unit itself. It is sufficient to have an "OLD" working and
memorised radio transmitter. The "NEW" radio transmitter will "inherit"
the characteristics of the OLD one; in other words if the old one is mem-
orised in Mode 1 then the NEW one will also be memorised in Mode 1;
in this case during the memorisation phase press any one key on the
two transmitters. If the OLD radio transmitter is memorised in Mode 2
press the key with the required command on the OLD transmitter and
press the key on the NEW transmitter with which you wish to associate
the new command.
Take the two transmitters and position yourself within the action range of
the automation and follow the following steps:
01. Press the key on the NEW radio transmitter for at least 5 s then
release it.
02. Press the key on the OLD radio transmitter slowly 3 times.
03. Press the key on the NEW radio transmitter slowly once.
At this point the NEW radio transmitter will be recognised by the control
unit and will take on the characteristics of the OLD one.
Repeat these steps for each new transmitter to be memorised.
1 time "Open" command
2 times "Pedestrian opening" command
3 times "Open only" command
4 times "Close only" command
5 times "Stop" command
6 times "Apartment block open" command
7 times "High priority open" command
8 times "Pedestrian opening 2" command
9 times "Pedestrian opening 3" command
10 times "Open + lock automation" command
11 times "Close + lock automation" command
12 times "Lock automation" command
13 times "Release automation" command
9.4.4 - Deleting a radio transmitter
It is necessary to have a radio transmitter to delete it.
If the transmitter is memorised in Mode 1 one single deletion phase is suf-
ficient and at point 3 any key can be pressed. If the transmitter is memo-
rised in Mode 2 a deletion phase must be carried out for each key.
01. Press the P1 key [B] key (fig. 24) on the control unit and hold it
down.
02. Wait until the LED P1 [A] (fig. 24) lights up, within three seconds.
03. Press the key on the radio transmitter to be deleted for at least three
seconds. If deletion is successful LED P1 will emit five quick flashes.
If LED P1 emits one slow flash it means that the deletion has not
been completed because the transmitter is not memorised.
04. To delete other transmitters keep key P1 pressed and repeat step 3
within 10 seconds otherwise the deletion procedure will end auto-
matically.
9.4.5 - Deleting all memorised radio transmitters
This procedure deletes all memorised transmitters.
01. Press the P1 key [B] key (fig. 24) on the control unit and hold it
down.
02. Wait until the P1 LED [A] (fig. 24) lights up, then wait until it goes off,
then wait until it has flashed 3 times.
03. Release P1 key precisely when the LED flashes the third time.
04. Wait about 4s for deletion to be completed, during which the P1 LED
will emit quick flashes.
If the procedure is successful after a few moments the LED P1 will emit
5 slow flashes.
24
TABLE 9
Commands the automation as described in table 3 (Open function)
Causes partial opening of one or two leaves as described in table 3 (Pedestrian
Opening)
Causes the leaves to open (open - stop - open etc.)
Causes the leaves to close (close - stop - close etc.)
Halts the manoeuvre
The command has no effect on opening, when closing the command causes the
movement to reverse, that is, opens the leaves
Works also when the automation is locked
Causes partial opening of leaf M2, equal to halfway
Causes partial opening of both the leaves, equal to halfway
Causes an opening manoeuvre and when this is complete, the automation is locked;
the control unit will not accept any command other than "High priority open" and
"Release" of the automation
Causes a closure manoeuvre and when this is complete, the automation is locked;
the control unit will not accept any command other than "High priority open" and
"Release" of the automation
Causes a halt of the manoeuvre and locks the automation; the control unit will not
accept any command other than "High priority open" and "Release" of the automation
Causes automation release and reset to normal operation
N M N M FLASH ECS bus STOP OPEN
A
B
English – 17