Bissell HYDROCLEAN COMPLETE 81N7 Mode D'emploi page 9

ImPoRTANT: be sure to use bISSell Hard
floor Solution when cleaning sealed hard
floor surfaces.
4. Place solution tank back in the machine.
5. Attach Microfibre mop pad to quick dry
hard floor tool by attaching ends to Velcro
strips on top of tool.
6. Attach quick dry hard floor tool to end
of the wand.
7. Plug into a proper electrical socket and
push heater, power and wet clean buttons on.
8. Place tool directly on the hard floor
surface, resting on the pad.
9. Press spray trigger to moisten mop pad
with cleaning solution.
Caution: Do not oversaturate.
10. Move tool back and forth across floor;
using solution, brushes and mop pad to
clean. Press spray trigger as needed.
11. With the spray trigger released, tilt the
tool forward and pull back across cleaned
floor to remove any residual water. This will
create the best suction and will help get the
hard floor surface as dry as possible.
12. Continue to clean entire floor.
13. When finished, be sure to remove
Microfibre mop pad and clean by hand
or machine wash as needed. Allow to
dry completely before next use.
14. Refer to section D for machine
care instructions.
D
Care,
Maintenance & Storage
d-1 machine care
1. Push heater, power and wet clean buttons
off. Unplug machine.
2. Open Quick Release™ hose door and
remove collection tank by lifting straight up
using tank handle.
3. Remove top lid from collection tank, rinse
and air dry.
4. empty dirty water into a sink, toilet
or outside by pouring dirt water out
from corner of tank. Rinse inside of
collection tank.
5. Remove mode selector by turning to
"ReMOVe" and pulling straight out.
6. Once mode selector is removed, remove
water filtration tower by lifting up and
rotating clockwise so front of tower is facing
side of collection tank. Then pull up and out
of collection tank.
7. Rinse collection tank, mode selector
and water filtration tower. Allow to air
dry completely before replacing water
filtration tower and mode selector
back into collection tank.
a. To replace filtration tower back
into collection tank, drop into top of
collection tank and rotate anti-clockwise
so front of tower is facing front of
collection tank. be sure to align with
tabs in bottom of collection tank.
b. Once water filtration tower is replaced,
replace mode selector by inserting back
into front of machine. Make sure mode
selector is in "ReMOVe" position when
inserting back into machine. Turn either
clockwise to "FilTeR VAC" or anti-
clockwise to "WeT CleAN" to lock
back in place.
8. For wet cleaning, remove all tools that
were used and rinse with clean tap water.
Allow to dry completely before storing.
9. Remove hose, taking care to keep both
ends up to avoid spilling. empty out any
remaining water and rinse clean with clean
tap water. Allow to dry completely before
storing or placing back on machine.
d-2 maintenance
1. Pre-motor filter: Remove from top lid
by pulling tab away from separator and
pulling straight out. inspect foam filter. if
dirty, rinse with clean tap water and allow to
dry completely before replacing back into
separator. To attach separator back onto
to top lid, line up "T" pieces under shallow
grooves on top lid and push together until
tab clicks together.
2. HePA Media filter*: Remove filter door by
pressing down on latch and pulling down.
Once filter door is open, place one hand on
each side of filter and pull it out of machine.
if dirty, replace with new filter or rinse under
clean tap water and allow to dry completely
before replacing back into machine. be sure
filter door is fully closed and latched prior to
operating machine.
d-3 machine storage
Water and cleaning formula can be left
in solution tank for next use.
1. Wrap power cable around cable wrap
on back of the machine.
2. store unit in a protected, dry area, at
room temperature (4° to 43° C).
WARNING
to reduce the risk of fire and
electric shock, always install float
before any wet pick-up operation.
www.bissell.com
9