Bissell HYDROCLEAN COMPLETE 81N7 Mode D'emploi page 7

A
Product View
Do not plug in your cleaner until you have
completely assembled it per the following
instructions and are familiar with all
instructions and operating procedures.
A-1 Water filter
Vacuum mode
1 Collection Tank Handle
2 Top Lid
3 Pre-Motor Filter
4 Collection Tank
5 Quick Release™ Hose Door
6 Mode Selector
7 Solution Hose
8 Solution Hose Hook-up
9 Wand Holder
10 Multi-Surface Vacuum Tool
11 Grip
12 Wand
13 Carry Handle
14 Tool Caddy & Tools
15 Power Button
16 HEPA Media Filter* Door
17 Long Power Cable
18 Air Flow Regulator
19 TurboBrush™ Vacuum Tool
A-2 Wet
clean mode
20 Spray Trigger
21 Grip
22 Carry Handle
23 Solution Tank
24 Wand Holder
25 Quick Release™ Cable Wrap
26 Heater Button
27 Measuring Cap
28 Power Button
29 Wet Clean Button
30 HEPA Media Filter* Door
31 Deep Clean Carpet
Washing Tool
32 3 Row Brush
33 EdgeSweep™ Brushes
34 Quick Dry Hard Floor Tool
35 Microfibre Mop Pad
36 Mode Selector
37 Quick Release™ Hose Door
Do not operate cleaner with damp or wet filters or
without all filters in place.
* The filter media, not the vacuum
as a whole, complies with the
iesT-RP-CC001.5 HePA standard.
38 Pre-Motor Filter
39 Top Lid
40 Collection Tank Handle
41 Collection Tank
42 Solution Hose
43 Solution Hose Hook-Up
A-3 cleaning
formulas
Always use genuine
bissell deep
cleaning formulas.
Non-bissell
cleaning formulas
may harm the
machine and will
void the guarantee.
44 1.5 L 2X Wash & Protect PRO
Professional Stain & Odour
Formula w/ Scotchgard™
Protection
45 1.5 L 2X Wash & Protect PET
Pet Stain & Odour Formula
w/ Scotchgard™ Protection
46 1.5 L 2X Wash & Protect
Stain & Odour Formula w/
Scotchgard™ Protection
47 1.5 L 2X Wash & Refresh
Ambi-Pur™ Blossom &
Breeze Formula
48 1.5L 2X Wash & Refresh Ambi-
PurTM Cotton Fresh Formula
49 1 L 2X Wash & Shine Hard
Floor Cleaner
50 650 ml Pretreat Stain
Pretreat
51 650 ml Pretreat PET Pet
Stain Pretreat
A-4 cleaning
Tools
52 TurboBrush Vacuum Tool
53 Multi-Surface Vacuum Tool
54 Deep Clean Carpet
Washing Tool
55 Quick Dry Hard Floor Tool
56 Tool Caddy
B
Assembly
1. Attach hose to Quick Release™ hose
door by inserting fitted end and turning
clockwise until it locks into place. Close
hose door.
2. Attach solution hose to machine by
inserting into hook-up and turning
clockwise until it locks into place.
3. Attach two wand pieces together by
lining up button locks with holes and
locking into place. be sure wand piece
with the storage bracket (see figure 4)
is the lower wand that will attach to tools.
Attach assembled wand to grip using
same technique.
4. Attach desired tool to lower wand and
place storage bracket into wand holder.
5. Place tool caddy on back of machine for
vacuuming or solution tank for wet cleaning.
C
Operations
Water filter vacuuming
ImPoRTANT: your cleaner is a water
filtration cleaner. NeVeR use it in filter
Vac mode without clean tap water in the
collection tank. you muST fill the collection
tank with clean tap water to the clean
water fill line on the back of the collection
tank for the machine to function properly.
Vacuuming in filter Vac mode without clean
water in the collection tank may cause
damage to the motor.
c-1 Getting ready
1. Open Quick Release hose door, turn
mode selector to "FilTeR VAC", then close
hose door.
2. Remove top lid from collection tank and
set aside.
3. Fill collection tank to clean water fill line
(located on back of tank) with clean tap
water and place top lid back onto top of
collection tank.
4. Attach desired vacuum tool to
end of wand (or directly to grip
for smaller accessories).
5. Plug into a proper electrical socket
and push power button on.
6. Refer to section D for machine
care instructions.
To reduce the risk of fire and electric shock due
to internal component damage, use only BISSELL
cleaning formula intended for use with the deep
cleaner. Non-BISSELL cleaning formula may harm
the machine and void the guarantee.
www.bissell.com
7