Cleco CWM-375 Serie Manuel Produit page 2

PL12-1083
02/02/2017
The original language of this manual is English.
Product Safety Information:
Intended Use:
These air impact wrenches are driven by compressed
air to assemble or remove threaded fasteners.
For additional product safety information refer to Apex
Tool Group, LLC or Apex Tool Group GmbH document
GS-2000, General Safety Air Assembly Tools.
WARNING
This impact wrench must not be modified in any
manner unless approved in writing by Apex Tool
Group, LLC or Apex Tool Group GmbH. All safety
devices must be properly installed and maintained in
good working order. Abuse, misuse, or failure to obey
this and any other issued warnings may result if injury
or death.
EC Declaration of Conformity:
We affirm that this machine is in accordance with
the following EC regulations (2006/42/EC). Applied
harmonized standards are ISO 12100:2010.
The name, job function and address of the person
authorized to compile the technical file.
Mr. William Cain
Director - Global Engineering Services
Apex Tool Group
670 Industrial Drive
Lexington, SC 29072
_______________________
Signature: William Cain
Date: February 02, 2017
Noise and Vibration:
Sound Level dB(A)
(ISO15744)
Model
† Pressure ‡ Power
(L )
p
Refer to the specification table in the back of this manual
for individual model sound level and vibration values.
† K = 3dB measurement uncertainty
pA
‡ Kw = 3dB measurement uncertainty
A
* K = Vibration measurement uncertainty
Air Line Lubrication:
Use Apex Tool Group, LLC or Apex Tool Group
GmbH's lightweight air tool oil 500021 (available in
quantities shown in the following chart) or an SAE-5
lightweight spindle oil.
Product Information
Vibration m/s 2
(ISO28927)
Level *K
(L )
w
EN
Part No. Packaged
540397 1 Quart (0.94 liter)
533485 1 US Gallon (3.78 liter)
Apply 2-3 drops of oil, into the air inlet, after 8 hours
of operation.
Air Supply Line:
Parameter
Minimum inside diameter: 3/8" (9.55mm)
Air Hose
Maximum length: 8.0' (2.4 m)
Working
Performance rated at: 90 psi (620 kPa)
pressure range
Air quality according to ISO 8573-1, quality
Compressed air class 2.4.3
The compressed air must be clean and dry.
Power or speed regulation system:
Models that include a Power Regulation System
allows the operator to select desired relative output
power or speed. To regulate the power, adjust this
system to the desired level as indicated on the tool.
It is recommended that if this feature is needed, that
you adjust to the lowest power setting and gradually
advance towards the maximum setting, as needed.
The indicators marked on the tool are for reference
ONLY and DO NOT indicate specific levels of power.
Many parameters will affect the ultimate power output,
including but not limited to: supplied air pressure,
quality, volume, dimension of air hose, actuation time
of tool, pressure applied to throttle, joint specifications,
etc. Calibrate the system, including the tool, to the
desired output level.
Service and Repair:
Tool service and repair should be performed by an
authorized Apex Tool Group, LLC or Apex Tool Group
GmbH Center. Refer to the last page of this manual
for locations.
Disposal:
Observe local disposal guidelines for all
components of this tool and its packaging.
Copyright Protection:
Apex Tool Group, LLC or Apex Tool Group GmbH
reserves the right to modify, supplement or improve
this document or the product without prior notice. This
document may not be reproduced in any way, shape
or form, in full or parts thereof, or copied to another
natural or machine readable language or to a data
carrier, whether electronic, mechanical, optical or
otherwise without the express permission of Apex Tool
Group, LLC or Apex Tool Group GmbH.
Page 2
Designation
Airlube 10W/NR-420LB DR
Airlube 10W/NR-420LB DR
Description