Faber 3 Step Mode D'emploi page 23

3. Do not tilt or move the fi re while there is water in the tank
or sump.
4. Make sure that the fi re is on a level fl oor.
5. The fl ame thumb wheel 'D' Fig. 2 may be turned up or down
to give a more realistic eff ect.
6. Sometimes the fl ames appear more real when the fl ame
thumb wheel is turned down.
7. Give the fl ame generator some time to react to changes
you may make on the fl ame control knob.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE
Fitting Replacement lamps.
If a large amount of the smoke appears grey or colourless it
may be that one or more lamps have failed.
You can check for lamp failure as follows.
1. Leaving the fl ame eff ect on, gently pull the drawer fully out
by the tab. (See Fig. 3)
2. View the lamps from a distance in front of the fi re and
observe which lamp needs to be changed.
3. Put Switch 'A' in the 'OFF' position, and unplug the fi re from
the mains.
4. Leave the appliance for 20 minutes to allow the lamps to
cool down before removing them.
5. Remove the water tank by lifting upwards and place in a
sink.
6. Remove the sump as described in the Cleaning Section.
7. Remove the defective lamp, by gently lifting vertically
and disengaging the pins from the lamp holder, (See Fig.4
and 5). Replace with an original, 12V, 50W, Gu5.3 base, 8º
beam angle, coloured lamp. Purchase the lamps from your
supplier
8. Carefully insert the two pins of the new lamp into the two
holes in the lamp holder. Push fi rmly in place. (See Fig. 4
and 5).
9. Replace the Sump and water tank and carefully close the
drawer.
10. Switch on.
Filling the water tank.
When the water tank is empty, fl ame and smoke eff ect shuts
off , and you will hear 2 audible 'beeps' . Follow these steps to
refi ll:
1. Press Switch 'A' to (0) (See Fig. 2)
2. Gently pull out the drawer as far as possible by the tab.
(See Fig. 3)
3. Remove the water tank by lifting upwards and outwards.
4. Place the water tank in sink and remove cap, Anti-clockwise
to open. (See Fig. 6)
5. Fill tank with tap water with a maximum hardness of 10
dH only. This is necessary to prolong the life of the fl ame
and smoke producing unit. In situations with a higher
water hardness, the water should be fi ltered (for example
with a Maxtra fi lter). Do not use a decalcifi er.
6. Screw the cap back on, do not overtighten.
7. Return the tank to the sump, with the tank cap facing down
and the fl at side of the tank facing outward.
8. Gently push the drawer back in as far as it will go.
9. Press Switch 'A' to 'ON' ( I ) position (See Fig. 2)
10. Press Switch 'B' once to turn on fl ame eff ect. (See manual
control section and Fig. 2)
Cleaning.
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
We Recommend cleaning the following components once
every 2 weeks, particularly in hard water areas:-
Water Tank, Sump and Seal, Sump lid, Tank cap and seal, Air
fi lter.
For general cleaning use a soft clean duster – never use abrasive
cleaners. To remove any accumulation of dust or fl uff the soft
brush attachment of a vacuum cleaner should occasionally be
used to clean the outlet grille of the fan heater.
Water tank
1. Remove water tank, as described earlier, put into sink and
empty water.
2. Using the supplied brush gently rub the inside surfaces of
the cap paying particular attention to the rubber ring in
the outer groove and the centre rubber seal.
3. Put a small quantity of washing up liquid into the tank, refi t
the cap and shake well, rinse out until all traces of washing
up liquid are gone.
4. Refi ll with fi ltered tap water only, replace the cap, do not
overtighten.
Sump
1. Press Switch 'A' to the 'OFF' (0) position
2. Gently pull the drawer out as far as possible. (See Fig. 3)
3. Remove the water tank by lifting upwards.
4. Disconnect the electrical connector, located on the left side
of the sump, by fi rst loosening the two retaining screws
and gently withdrawing the connector. (See Fig. 8)
5. Release the lower sump locking tabs by turning 90°, this
allows the sump to be lifted completely from its location.
(See Fig. 9)
6. Gently lift up the sump assembly, taking care to keep level
so as not to spill any water. Sit the assembly in the sink.
(See Fig. 10)
7. Release the two upper sump locking tabs by turning 90°,
then lift off the sump lid. (See Fig. 11)
8. Carefully tilt, as shown, so that the liquid drains out of the
sump. (See Fig. 12)
9. Put a small amount of washing up liquid into the sump,
and using the supplied brush, gently clean all surfaces
including the metal disc and the rubber seal located in the
top grooved surface. Do not remove the rubber seals.
(See Fig. 13 and 14)
10. When cleaned, thoroughly rinse the sump with clean
water.
11. Clean the outlet surface of the sump lid with the brush and
fl ush out thoroughly with water. (See Fig. 15 & 16)
12. Reverse the above steps to reassemble.
Air fi lter.
1. Press Switch 'A' to the 'OFF' (0) position (See Fig. 2)
2. Gently pull the drawer out as far as possible. (See Fig. 3)
3. Remove the tank and place in a sink with the cap facing
upwards.
4. Gently slide upwards the air fi lter plastic holder. (See
Fig. 17)
5. Remove the fi lter combination from the plastic holder.
6. Gently rinse with water in the sink and dry with fabric towel
before returning.
18