Operation - SPARKY HeavyDuty SMA 18Li HD Notice Originale

ACCESSORIES TO BE USED WITH THIS
POWER TOOL
25. Hook-and-loop sandpaper (Velcro type)*
26. Hook-and-loop foam pad (Velcro type)*
* The additional accessories shown in the illustrations or
described in the text are not included in the delivery.

Operation

This power tool is designed for rough and fine dry sand-
ing and polishing difficult to access metal or wood sur-
faces by means of sandpaper, felt wheels or foam pads
(Velcro type), for example for sanding window shutters,
gaps or radiator fins.
WARNING: Operating this power tool with
accessories, different from the described herewith,
may cause accident during operation. The possibility
to attach an accessory to the machine does not imply
that the machine is designed to be operated with it!
Any use of this tool with accessories, different from the
described herewith, and the resulting danger for your
health are entirely AT YOUR OWN RISK.
PRIOR TO INITIAL OPERATION
▪ Check the position of ON/OFF switch. The battery
shall be connected and disconnected to the pow-
er tool only when the switch is in OFF position. If
the battery is connected to the power tool with the
switch in ON position, the machine will not start, be-
cause the non-self starting safety (NVR) will be ac-
tuated. To start the power tool you must first switch
it off and then on again.
WARNING: Always switch off the power tool
and remove the battery prior to any adjustment, servic-
ing or maintenance.
▪ Check if the operating tool diameter does not exceed
the size stated in the specifications.
▪ Check that the auxiliary handle is properly mounted
and reliably tightened.
▪ Check that the fixing screws (10) are firmly fastened
and tighten them if necessary.
FITTING AND REMOVING THE
BATTERY PACK (Fig. 1)
To remove the battery: Press release button (5) in the
indicated direction and pull the battery out of the ma-
chine body.
To insert the battery: Place the battery into the base of
the machine and slide it until it locks with an audible click.
BATTERY STATE INDICATOR (Fig.2)
Battery state can be checked on the LED display (13).
To activate the indicator, press button (12).
Original instructions
Battery capacity: 60 - 100%
Battery capacity: 30 - 60%
Battery capacity: < 30%
Battery capacity: < 20%. The battery
must be recharged.
Blinking light
Problems with battery. The display is
activated upon pressing the trigger of
the switch. It may show one of the fol-
Blinking light
lowing battery states:
▪ Low battery ► Battery has to be
recharged;
▪ Temperature protection has been
actuated ► Battery must be cooled
down prior to resuming operation;
▪ Damaged or unrecognized battery
► Battery has to be replaced
Current overload: The display is
active during operation with the ma-
chine. Upon current overload the pro-
Blinking light
tection switches off the machine. To
restore normal operation first switch
off and then on switch (3).
Non-self starting safety (NVR).
Indication is activated upon connect-
ing battery to machine with its switch
in ON position. To run the machine
you must first switch off and then on
switch (3).
SWITCHING ON - SWITCHING OFF
Switching on: Push the back end of the ON/OFF switch
(3) down and then forward in the direction of the arrow
until its front end will sag, thus fixing itself.
Switching off: press the back, lifted end of switch (3)
and release it to return in its initial position.
SELECTING THE ACCESSORY AND
PREPARATION FOR OPERATION
The choice of the accessory depends on the intended
operation. Generally the operations you are allowed to
perform are:
- Sanding with sandpaper;
- Sanding with felt wheel;
- Polishing with a foam pad.
USING THE OPERATING TOOL
The selection of sandpaper depends on the desired
surface quality. For rough operations use sandpaper
with larger grit size, and for fine and finishing operations
use sandpaper with smaller grit size to achieve surface
smoothness.
Use only hook-and-loop sanding accessories (Velcro
type).
Do not use sanding accessories with diameter exceed-
ing the maximum diameter permitted for this power tool.
7
EN