53 5.4 Weight Transfer From; 53 5.5 Blocking «High Values; 53 5.6 «Attn Credit» Display; 53 5.7 No Credit Loaded - Frama EcoMail Mode D'emploi

• Enter (50) and confirm by pressing the
«OK» key.
→ The working menu reappears.
→ «STACK 50» is displayed in the stack
key field.
• Place the letters on the feeder table.
→ The machine franks the previously sel-
ected quantity of letters.
→ The mail item counter in the «STACK»
key field counts down to zero.
→ The system halts after franking the
previously selected quantity of letters.
• To repeat the procedure, briefly lift the
remaining stacked letters and replace
them on the feeder.
→ The procedure repeats itself.
Important: The pre-selected quantity re-
mains stored until cleared by pressing the
«CE» key.
5.4 Weight transfer from connec-
ted weighing platform *
If a Frama scale or weighing platform is
connected, the weight value for the posta-
ge calculation and settings can be transfer-
red from the scale to the franking machine
as follows:
Weighing
• Place the mail item on the scale.
• Press the «WEIGHT» key.
→ The Enter weight menu field appears.
• Press the «STANDARD SCALE» key.
→ Switches back to the working menu.
→ Displays «SCALE» and the weight in
the weight key field.
→ Postage displayed in inverse type.
• Remove mail items from the weighing
platform.
• Confirm value and frank.
• Place the next mail item on the scale and
press the weight key, etc.
5.5 Blocking «High Values«
You can program an upper postage limit in
the Info/Setup menu (section 5.9.20). This
prevents franking at excessive values. If the
programmed limit is reached or exceeded
during a postage calculation or a value set-
ting, a «HIGH VALUE» warning appears in
the value indicator field. The system then
remains blocked for franking until the war-
ning is acknowledged by pressing the value
indicator field. Following the next franking,
the system is again blocked. Press again af-
ter each franking to override. If you are
using the LF8500 automatic letter feeder,
the high value must be confirmed for every
restart (loading further letters, or lifting the
remaining stack when franking a pre-selec-
ted number of letters with the same value).
5.6 «ATTN CREDIT« display *
If the remaining credit falls below 25% of the
total available credit after the last credit loa-
ding, an «ATTN CREDIT» warning signal ap-
pears in the value indicator field (only for coun-
tries having remote postage resetting). See sec-
tion 5.9.24 to carry out a credit loading.
5.7 No credit loaded *
If a franking value is set and there is insuffi-
cient credit (for countries having remote
postage resetting), you will not be able to
frank. This condition is shown on the dis-
play with «No credit loaded». To reload,
see section 5.9.24.
5.8 Stamping die switch-on,

switch-off *

5.8.1 Date switch-on/off *
In some countries, it is permitted to switch
off the date and location stamp when fran-
king.
Procedure:
• Press the date stamp field.
→ The date stamp is switched off.
→ Instead of the date, «OFF» appears.
• Again press the date stamp field.
→ The date stamp is switched on again.
→ The current date is again displayed.
5.8.2 Selecting the ad cliché
Up to eight separate ad clichés can be read
into the Mailmax franking system using a
special ad cliché loading box (see section
6). Ad clichés programmed in this way may
be printed on mail items as follows:
• Press the «ADVERT. 1» key (1 means that
ad cliché 1 is currently activated).
→ The first four stored ad clichés are dis-
played.
• Press the «NEXT PAGE» key to display
any other stored clichés.
53