Publicité
Les langues disponibles
Les langues disponibles
Locations 34 and 51
5
Zone tamper reporting
6
Cancel reporting
7
Recent closing reporting
8
Exit error reporting
Location 51
1
Disable on-board 8 zones.
Segment 2
2
Force default configuration for zone
types to be used.
3
Disable report bypass on force arm.
4
Enable resetting of tamper memory by
a master code.
5
Enable 2 wire smoke detectors to be
used.
6
Sets for 25VA transformer.
7
Enable first to open / last to close.
8
Enable summer / wintertime option.
Location 51
1
Box tamper reporting
Segment 3
2
Mains fail reporting
3
Low battery reporting
4
Aux. Power overcurrent reporting
5
Siren supervision reporting
6
Reserved
7
Reserved
8
Expander trouble reporting
Location 51
1
Reserved
Segment 4
2
Log full reporting
3
Autotest reporting
4
Start/end programming reporting
5
End download reporting
6
Sensor low battery reporting
7
Sensor missing reporting
8
Automatic test reporting only when
system is armed
Location 51
1
Lost clock service LED
Segment 5
2
Enable All Abort
3-8
Reserved
Table 3 Enabling event reporting
Programming zone types
Each zone is programmed to be one of 20 possible zone types.
Assign the zone type for zones 1 to 8 in location 36 in the control
panel. Assign the voice message for zone types 1 to 20 in
location 128 onwards (in increments of four locations). See table
4 for a list of locations that correspond to the various zone types.
Location
128
132
136
...
Table 4 Locations and zone types
Press # &
1.
#
to program the zone type.
Press ! !
2.
in segment 1 to set zone 1 as a 'Burglary'
zone type.
3.
Program each zone required for voice reporting in this way.
W
CS535
ORKING WITH THE
VOICE MODULE
Loading factory defaults for the CS535 voice module
1.
Enter programming mode.
Press ' '
2.
#
to program the CS535 voice module.
Press ) ! *
3.
#
to reset the module.
4.
The keypad beeps three times to indicate that loading is in
progress. This takes about six seconds.
Zone Type
1
2
3
...
6
Recording messages
1.
Connect a telephone handset to the phone jack on the
CS535 voice module. See figure ! 5.
2.
Enter programming mode.
Press ' '
3.
#
to program the CS535 voice module.
Press *
4.
to program recording/playback options.
#
Press !
5.
in segment 1 to enter recording mode.
6.
Complete one of the following steps depending on the
message(s) you want to record.
•
To record all messages, press ! %
and press
in segment 3.
•
To record the leader message, press *
2 and press
in segment 3.
•
To record the address message, press #
segment 2 and press
•
To record a single event message, press !
segment 2. Enter the number of the message (1 to 15)
in segment 3 and press
•
To record a range of event messages, press "
segment 2. Enter the number of the first message in
segment 3 and press
•
To record a kiss off message, press $
2 and press
in segment 3.
7.
Press the record/playback button on the CS535 voice
module and record the message. See figure ! 7.
8.
If you are recording a range of messages, continue
recording each message until you have finished. Otherwise,
press the recording/playback button to stop recording. The
message is played back.
<
If you make a mistake and want to stop recording at
*
any time, enter
in segment 1. Press
location
.
9.
If you are satisfied with the message, press the
recording/playback button to record the next message in the
same way.
<
Do not start recording the next message while the
record/playback LED is lit.
10.
To re-record a message, press the recording/playback
button twice in quick succession and re-record the
message.
11.
Record all messages finishing with the address message.
Message
Maximum
Type
Duration
Leader
Address
Alarm / Event
7,5 s
Table 5 Message lengths
Playing back messages
1.
Connect a telephone handset to the phone jack on the
CS535 voice module. See figure !Å 5.
2.
Enter programming mode.
Press ' '
3.
to program the CS535 voice module.
#
Press *
4.
#
to program recording/playback options.
Press " £
5.
in segment 1 to enter playback mode.
6.
Complete one of the following steps depending on the
message(s) you want to playback.
in segment 2
in segment
in
in segment 3.
in
.
.
in segment
#
to exit the
Number of
Messages
20 s
1
20 s
1
16
in
Publicité
