Publicité
Les langues disponibles
Les langues disponibles
4.
Enter each digit of the phone prefix and press
digit. For example, if the phone prefix is 222, press "
"
.
•
Keys * to ) represent digits 0 to 9.
•
Enter ! ! to program the star key as the prefix.
•
Enter ! " to program the hash key as the prefix.
•
Enter ! # to program a four second delay at any
point in the prefix.
•
If pulse dialling is required, enter ! % in the segment
where pulse dialling begins. If the entire number is
pulse dialling, enter ! %
•
Tone dialling is enabled by default.
5.
If the prefix is less than four digits long, program the last
digit and press ! $
#
to exit the location
remains in programming mode.
Setting phone numbers
1.
Enter the relevant location and press
of phone locations. For example, press "
phone number 1.
2.
Enter each digit of the phone number and press
the complete number has been entered.
3.
If the number is less than 16 digits long, program the last
digit and press ! $
#
to exit the location
remains in programming mode.
Phones
Number
2
Phone 1
6
Phone 2
10
Phone 3
14
Phone 4
18
Phone 5
22
Phone 6
Table 1 Phone locations
Setting the communicator format
#
Press $
1.
to set the communicator format for phone
number 1.
Press $
2.
.
<
3.
It is necessary to set the communicator format for phone
number 1 only. See Setting up phone numbers in part 1 for
more information.
Configuring reportable events
You must program the events to be reported to each phone
number. There are 15 events represented by numbers 1 to 8 in
two segments.
Segment 1
1
Alarms
2
Reserved
3
Opening and closings
(Armings and
Disarmings)
4
Zone bypass
5
Zone trouble
6
Power fail, low battery
7
Bell cut
8
Test reports
Table 2 Reportable events
1.
Enter the relevant location and press
of phone locations. For example, press %
events for phone number 1.
after each
in segment 1.
. The control panel
#
. See table 1 for a list
#
to program
when
. The control panel
Communicator
Events
format
4
5
8
9
12
13
16
17
20
21
24
25
Segment 2
1 Start and end programming,
download complete
2 Zone and box tamper
3 Auxiliary power overcurrent,
ground fault
4 Wireless sensor missing
5 Wireless sensor low battery
6 Expander trouble
7 Reserved
8 Zone activity monitor
#
. See table 1 for a list
#
to program the
2.
Event numbers 1 to 8 are displayed. See table 2 for an
explanation of each number.
"
3.
Press the corresponding digit on the keypad to enable or
disable an event. Events that are not reported are indicated
by a hyphen (–).
4.
Press
to configure events in segment 2. Enable or
disable events as outlined in step 3.
5.
When you have finished programming events in segment 2,
press
to exit the location
programming mode.
Setting the number of dial attempts
#
Press " &
1.
to program the number of dial attempts.
2.
Press
to enter segment 2.
3.
Enter the number of dial attempts (1 to 15) and press
The default depends on the country code.
Setting dialler delay
Press " (
1.
#
to set a dialler delay.
2.
Enter the length of the dialler delay (0 to 255 seconds).
Enabling abort all reports
Press % !
1.
#
to enable the all abort function.
2.
Press
3.
Report options are displayed. Digits 1 to 8 represent
enabled options. Hyphens represent disabled options.
4.
Press the corresponding digit on the keypad to enable
option 2 and press
5.
Press
to return to the device prompt.
C
ONFIGURING THE CONTROL PANEL FOR VOICE REPORTING
You must enable event reporting in the control panel and program
the zone types for which reports are sent.
Enabling reporting
To enable event reporting, you must program locations 34 and 51
on the control panel. Location 34, segment 3 enables
communicator reports and features that can be accessed by, or
are visible to, the user from the keypad. Location 51 enables
system features and reporting options.
1.
Enter programming mode.
#
Press *
2.
to select the control panel device.
#
Press # $
3.
to enter location 34.
4.
Press
to enter segment 3.
5.
Event numbers 1 to 8 are displayed. See table 3 for an
explanation of each number.
6.
Press the corresponding digit on the keypad to enable or
disable an event. Events that are not reported are indicated
by a hyphen (–).
7.
When you have finished programming events in segment 3,
press
to exit the location.
in programming mode.
Press % !
8.
#
to enter location 51.
9.
Press
to enter segment 2.
10.
Program the events in segments 2, 3, 4 and 5 using the
mechanism described in steps 5 to 7.
Locations 34 and 51
Location 34
1
Segment 3
2
3
4
5
. The control panel remains in
to enter segment 5.
.
The control panel remains
Opening and closing reporting
Zone bypass reporting
Reserved
Zone trouble reporting
.
Publicité
