Monacor TVCCD-160SCOL Mode D'emploi page 6

Please unfold page 3. Then you can always see the
GB
operating elements and connections described.
1 Connections and Operating Elements
1.1 Camera
1 Lens
2 Screw sleeve
3 Thread jacks (6.3 mm/
4 Connection cable to the power supply unit
1.2 Bracket
5 Thread bolt to mount the camera
6 Knurled nut
7 Ball joint
8 Setscrew
1.3 Power supply unit
9 POWER LED
10 POWER switch
11 Mains cable for the connection to 230 V~/50 Hz
12 Fuse holder; only replace a blown fuse by one of
the same type
13 Four sliding switches for video level matching or
compensation of level losses when using a long
connection cable to the camera;
adjustment see table on page 7
14 Video output for the monitor connection
15 Jack to connect the camera
(video input and operating voltage output for the
camera)
2 Safety Notes
The units (power supply unit and camera) correspond
to all required directives of the EU and are therefore
marked with .
WARNING The power supply unit is supplied with
hazardous mains voltage (230 V~).
Leave servicing to skilled personnel
only. Inexpert handling may cause an
electric shock hazard.
Observe in any case the following items:
The power supply unit is suitable for indoor use only.
Protect the units against heat (admissible ambient
temperature range -10 °C to +50 °C) and the power
supply unit additionally against dripping water,
splash water, and high air humidity.
Do not place any vessels filled with liquid, e. g. drink-
ing glasses, on the power supply unit.
6
All manuals and user guides at all-guides.com
1
/ ") to mount the bracket
4
The camera housing is watertight according to IP 68,
i. e. maximum water depth 1 m and maximum time of
immersion 2 days.
The heat being generated in the power supply unit
has to dissipate via air circulation. Therefore the
vents of the housing must not be covered.
Do not insert anything into the vents! This could
result in electric shock.
Do not set the power supply unit into operation, and
immediately disconnect the mains plug from the
mains socket if:
1. there is visible damage to the units or to the mains
cable,
2. a defect might have occurred after a drop or simi-
lar accident,
3. there are malfunctions.
The units must in any case be repaired by skilled
personnel.
A damaged mains cable must only be replaced by
the manufacturer or skilled personnel.
Never pull the mains cable to disconnect the mains
plug from the mains socket, always seize the plug.
For cleaning do not use any strong detergents or
chemicals. For the power supply unit only use a dry,
soft cloth.
No guarantee claims for the units or liability for any
resulting personal damage or material damage will
be accepted if the power supply unit or the camera
is used for other purposes than originally intended, if
it is not correctly connected, operated, or not re-
paired in an expert way.
Important for U.K. Customers!
The wires in this mains lead are coloured in accord-
ance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed!
If the units are to be put out of operation de-
finitively, take them to a local recycling plant
for a disposal which is not harmful to the envi-
ronment.