Shared Flue Gas System; Air Supply; Dimensional Drawing; Technical Information - Nordpeis Lisboa Manuel D'installation

tested and should be connected to a chimney that is
dimensioned for the smoke gas temperature indicated
in the CE declaration. When necessary, contact a
professional in advance.

Shared flue gas system

Appliance can be connected to shared flue gas pipe
system. In case of simultaneous operation with other
heating appliances, there must be sufficient combustion
air provided.
Warrning! In case of the appliance connected to
shared flue gas pipe system - the Sefl Closing Door
system must be operational.

Air supply

A set for fresh air supply is available as accessory.
This will ensure that the air supply to the combustion
chamber is less affected by ventilation systems,
kitchen fans and other factors which can create a
down-draught in the room. In all new construction, we
strongly recommend that it is designed and prepared
for direct supply of outside air. In older houses, the use
of fresh air supply set is also
air supply can cause down-draught and thereby low
combustion efficiency and the problems that this entails:
soot stains on the glass, inefficient use of the wood and
a soot deposits in the chimney.
Warning! Keep the air intakes, supplying
combustion air, free from blockage.
If the requirements for ventilation are
NOT complied with, the product can overheat.
This can cause a fire.
Warning!
Extractor fans when operating in the same room or
space as the appliance may cause problem.

Dimensional drawing

The illustrations indicate the approximate centre height
of the hole for the flue. Distortions in floors and walls
may influence the dimensions. Dry stack the fireplace
without glue for accurate height and positioning of the
flue/chimney connection.

3. Technical information

All products Nordpeis have secondary combustion and
are clean burning. The combustion takes place in two
phases: First the wood burns and then the gases from
the fumes are lit by the hot air. This ensures that these
new fireplaces have minimal emissions of soot particles
and un-burnt gases (such as CO) and are thus better
for the environment. Clean burning fireplaces require
a small amount of wood in order to obtain a good heat
output. Use exclusively clean and dry wood.
4
recommended. Insufficient
Weight incl.insert
Material insert
Insert
Surface treatment door/
doorframe
Fuel
Operating range
Efficiency
CO % @ 13% O
2
Draught system
Combustion system
Flue outlet
Flue
Flue gas temperature
Air supply
requirements (m³/h)
Fuel charge
Refueling interval
Opening of the air vent
control
Operation
* Intermittent combustion refers to normal use of a fireplace, i.e. new
wood is inserted when the previous load has burned down to ember
Warning: If the requirements for ventilation are
NOT complied with, the cooling airflow around the
product will be considerably reduced and
the product can overheat.
This can cause a fire.

4. Safety distances

Ensure that the safety distances are complied with
(FIG 2).
When connecting a steel chimney to the top outlet
follow the assembly instructions from the producer.
Ensure to comply with the security distances required
for the steel chimney.

5. Assembly

Assembling of a bracket leg - FIG5
The insert is delivered with two assembled front legs.
Before you start assembling the surrounding you need
to assemble bracket leg to the insert - see FIG5. The
bracket leg is longer than front legs, it's advisable to
place under the front legs e.g. a 70 mm wooden block
in order to keep it in upright position.
Initial setting the blocker - FIG6
The insert has a blocker to keep insert in position in
use, after it is assembled.
Before assmebling, the blocker has to be checked.
GB
121 kg
Sheet steel
S-18U
Heat resistant varnish
Wood logs 30 cm
4 kW nominal
82%
0,07
Air vent control
Secondary combustion (clean
burning)
Top and rear
Outer Ø 150 mm
*Alternative versions exsists due to
National requirements
262 °C
3
9-13 m /h
1.3 kg
50 min
33%
Intermittent*