stayer OLMO G-1 250 C Instructions D'emploi page 23

Thank you very much for acquiring a STAYER
product!
This manual covers
OLMO G2-400B, OLMO G3-450C with gasolina engine
and one model, OLMO 22-400B, with an electric engine.
The safety features
comply with all international
They include hand guards at both handles, a handle safety
device, a chain ratchet, a safety chain and a chain brake.
The chain brake may be actuated manually or it is also
actuated automatically by inertia in case of occurrence of
repulsion.
To ensure appropriate operation and performance
of your new chain saw and to safeguard your own
safety, it is mandatory that you carefully read this
instruction manual befare using the chain saw.
Take special care in observing all safety precautions!
If you do not observe these precautions you may
suffer severe injuries or even die!
Packaging
Your STAYER chain saw will be delivered to you in a pratective
cardboard box so as to avoid damages during transport.
Cardboard is a basic commodity and thus reusable and
suitable far recycling (recycling of used paper).
Specific safety instructions
This chain saw has been especially designed for
conserving and taking care of trees.
Any work with this
carried out by duly
Observe all specialized literatura, and the pracedures
and recommendations of the relevant prafessional
organizations. lf you do not do so, you will run the risk
of suffering an accident! We recommend to always
use an elevator platform (platform far collecting
fruit, elevator) to cut in trees. Climbing techniques
using rapes are very dangeraus and require special
training! The operator must be trained and be familiar
with the use of safety equipment and working and
mountaineering techniques! Always use suitable belts,
rapes and snap hooks when working in trees! Always
use fastening equipment far both yourself and the
chain saw!
Safety precautions
General precautions
To ensure correct operation, the used must read this
instruction manual so as to become familiar with the
features of the chain saw. Users who are little informad
will put at risk their own lives and those of others, due to
incorrect handling.
- Borraw this chain saw only to persons with training and
experience in the use of pruning chain saws. Always
hand out the instruction manual.
models OLMO G1-250C,
are very modern
safety standards.
chain saw must
trained persons only.
lllustrated description
1 Rear handle
2 Safety locking button (locking of the accelerator)
3 Accelerator lever
4 Hand guard (ralease far braking the chain)
and
5 Chain
6 Guide bar
7
Guide bar cover
8 Retaining nuts
9 Chain ratchet
10 Pin ion cover
11 Muffler
12 Spark plug
13 Frant handle (tubular handle)
14 Starter handle
15 ON/OFF switch (circuit breaker switch)
16 Chain adjusting screw
17 Oil tank lid
18 Fan housing with starter device
19 Fuel tank lid
20 Air filter cover
21 Throttle lever
22 Priming pump
23 Air cover lid
24 Air filter (clean with gasolina and then with compressed
air)
25 Monkey key
26 Rat tail file
27 Adjusting screw "H" (high speed)
28 Adjusting screw "L" (low speed)
29 Adjusting screw "T" (idling)
30 Screw driver
31 Chain tensioner for electric models
32 Drive sprocket for cutting chain
be
Startup
Connection to electric power supply (OLMO 22-400B)
ALERT: Make sure that you connect your machina to
an electric installation complying with applicable legal
regulations including connection of the equipment by
means of a magnetothermal switch.
ATTENTION: This equipment has a class II electric
protection degree with double insulation.
Check the cabling device far perfect performance and
safe operating conditions.
Make sure that lubrication of the chain is correct and the
level of oil adequate. Check the tension of the chain and
operation of the chain brake.
WARNING: Make sure that the power supply cable is in a
good condition. Never use a damaged cable.
Before carrying out any work at the guide bar or chain,
always stop the engine and extract the spark plug
cap (refer to "Replacing the spark plug"). Always wear
protective gloves!
Do not start the chain saw before it has been completely
assembled and cheked.
Assembling the guide bar and saw chain
Always use the monkey key (25) as delivered together
with the chain saw far carrying out the fallowing work.
/ /
23
es
it
gb
fr
p
el