STEINEL PROFESSIONAL HF 3360 Instructions De Montage page 8

Manual override function
If a mains switch is installed in the mains sup-
ply lead, the light is capable of the following
functions in addition to the simple ON/OFF
function:
2 x aus/an
1 x OFF/ON
5 sec. – 15 min. 4 Stunden
2 x aus/an
2 x OFF/ON
4 Stunden 4 hours
Technical specifications
HF 3360
Dimensions: (l x w x h) 95 x 95 x 57 mm
Output: • 2000 W max., VDE tested
(resistive load, e.g. filament bulb)
• 10 AX max., VDE tested (fluorescent tube)
• 900 W max. (series corrected)
• 500 W max. (parallel corrected,
at C = 45.6 µF)
• 600 W max. (electronic ballasts, capacitive, e.g.,
low-energy lamps, 8 each max.)
Mains power: 230 – 240 V, 50 Hz
Recommended mounting height: 2.5 m
Installation site: inside buildings
Sensor system: 5.8 GHz high-frequency
Transmission power: approx. 1 mW
Angle of coverage: 360° with 180° angle of aperture,
if necessary also through glass, wood and stud walls
Reach: 1 – 8 m continuously adjustable
Twilight setting: 2 - 2000 lux
Time setting: 5 sec. - 15 min.
Manual override: selectable (4 h)
Enclosure: IP 54
PK Elektronik Vertriebs GmbH, E-Mail: info@pkelektronik.com, Internet: www.pkelektronik.com
Important: The switch should be actuated in
rapid succession (in the 0.5 – 1 sec. range).
Sensor operation
1) Switch light ON (when light is OFF):
Turn switch OFF and ON once.
Light stays on for the period selected.
2) Switch light OFF (when light is ON):
Turn switch OFF and ON once.
The light goes out or switches over to sensor
mode.
Manual override
1) Select manual override:
Turn switch OFF and ON twice. The lamp is
set to stay on for 4 hours (red LED lights up).
Then it returns automatically to sensor mode
(red LED off).
2) Deactivate manual override:
Turn switch OFF and ON once. The light goes
out or switches over to sensor mode.
14
Troubleshooting
Malfunction Cause
Sensor without power Fuse faulty, not switched ON
Short circuit
Additional two-way switch
OFF
Fuse faulty
Sensor will not switch ON Bulb faulty
Twilight control set to night-
time mode during daytime
operation
Additional two-way switch
OFF
Fuse faulty
Sensor will not switch OFF Continuous movement in the
detection zone
Manual override activated
(red LED lights up)
Another sensor is parallel-
connected and still active
Sensor keeps switching Curtains, plant etc. moving
ON/OFF in the sensor's detection
zone causing the sensor to
respond
LED flashes rapidly Load connected is too high
(approx. 5 x per second)
Functional warranty
This STEINEL product has been manufactured
with the utmost care, tested for proper oper-
ation and safety in accordance with applicable
regulations and then subjected to random
sample inspection. STEINEL guarantees that it
is perfect condition and proper working order.
The warranty period is 36 months, starting on
the date of sale to the consumer. We will rem-
edy defects caused by material flaws or manu-
facturing faults. The warranty will be met by
repair or replacement of defective parts at our
own discretion.
This warranty shall not cover damage to
wearing parts, damage or defects caused by
improper treatment or maintenance.
Further consequential damage to other objects
is excluded.
Remedy
New fuse, turn on power
switch, check wiring with
voltage tester
Check connections
Switch ON
New fuse, check connec-
tions if necessary
Change bulb
Reset
Switch ON
New fuse, check connection
if necessary
Check zone
Deactivate manual override
Wait for time setting of the
other sensor to elapse
Check zone
Reduce load or use
contactor
The warranty will only be honoured if the
product is sent to the appropriate Service
Centre fully assembled and well packed with
a brief description of the fault, receipt or in-
voice (date of purchase and dealer's stamp).
Repair Service:
Our Customer Service Department will repair
faults not covered by warranty or occurring
after the warranty period has
expired. Please send the prod-
uct well packed to your nearest
Service Centre.
15