tau ZIP Manuel D'emploi Et D'entretien page 14

INSTALLATION MATERIALS (fig. 2)
1_ cod. P-650ZIP
2_ cod. P-150BAR
3_ cod. S-150BAR0020
4_ cod. S-150BAR0030
5_ cod. S-650RBS0030
PRESENTING THE AUTOMATISM
It is necessary to make a distinction between two motorization types:
1_ reversing motor =
2_ non reversing motor =
Consequently we suggest installing the electric lock in two cases:
1 - the motor is of the reversing type and wing length exceeds 1.6 metres
st
2 - irrespective of the type of motor, if the wing is very long and consequently subject to oscillation during the opening and closing
nd
manoeuvres.
Upon request the ZIP gearmotor can be provided with limit switches inside the motor.
CONSIDERATIONS PRIOR TO INSTALLATION
The system you have chosen brilliantly resolves all the most common problems that may arise in the residential type installations but
there are just a few suggestions we would like to make:
1. Install the gear motor as near as possible to the gate you wish to automatize; never install it anywhere-it would hinder opening.
2. Since the length of the articulated arm determines the fixing point of the bracket for hooking to the gate, we suggest that:
- keeping the length of the part of the arm connected to the motor at least two or three centimetres longer than its minimum length;
- keeping the length of the part of the arm connected to the gate just a few centimetres shorter than its maximum length.
3. Before fixing the bracket try and move the gate manually (with the gearmotor disconnected) and see whether or not the automation
can open to the extent required.
Note: for complete safety, the mechanical stops with rubber cap (floor stops) must be fitted in opening and closing of the gate, as
shown in fig. 13 and in fig. 14.
ANCHORING THE PLATE (fig. 3)
To secure them use expansion bolts (with brickwork pillar) or bore and tap (if the plate is joined to a metal structure).
FIXING THE BRACKET FOR HOOKING TO THE GATE (fig. 4)
Use self-threading screws to fix the bracket where established according to the selection "Considerations prior to installation".
INSTALLING AND ANCHORING THE GEARMOTOR
The arm is of the articulated type so it is necessary, during installation, to determine the correct position when both wings are closed
(explained in fig. 5). Unlock the gearmotor to facilitate operations.
After having fixed the anchoring plate and bracket, proceed as follows:
1_ anchor the gearmotor to the plate using 4 M6x120 hexagonal head screws, 4 washers Ø 6x12x1,2 and 4 M6 high self-locking nuts as
shown in the drawing;
2_ to fasten, make use of the 4 through holes on the gearmotor aluminium case; place the washer between the nut and the motor;
3_ secure the rod with boss to the motor output shaft, by fixing a bolt; make sure the rod is firmly secured and cannot come away ac-
cidentally during use;
4_ with the screw and nut secure the rod with holes to the bracket fixed to the gate wing;
5_ after passing the cables for the electrical connection, using the holes on the plate, put the casing in position and secure it with the 2
M6x40 screws as shown in fig. 7 and in fig. 8.
MANUAL UNLOCK (fig. 9 - fig. 10)
To carry out the manual lock, proceed as follows:
1. Lift the knob
2. Screw the knob to push the release pin.
ELECTRICAL CONNECTION TO THE MOTOR
• Connect, making use of the free hole in the anchoring plate.
• Protect the cables with a flexible sheath.
• Minimum cable section should be1,5 mm².
• By reversing connections, the motor should reverse rotating direction.
Place the control unit (external versions) in the immediate vicinity of the
Be careful not to run cables for auxiliary devices inside raceways housing other cables supplying power to large loads
or lights with electronic
In the event control pushbuttons or indicator lights are installed inside homes or offices several metres from the
actual control unit, it is advisable to decouple the signal by means of a relay in order to avoid induced
ZIP gearmotor
articulated arm + anchoring plate
rod with boss for jointed arm
rod with holes for jointed arm
bracket
the automatism is not fitted with a release.
the automatism is fitted with a release.
starters.
6_ cod. M-V350AM12A0 M12 high self-locking hexagon nut
7_ cod. M-V100012035I stainless M12x35 hexagonal head screw
8_ cod. M-V500012036I plain washer D.12x36
9_ cod. M-V500008024I plain washer D.8x24
10_ cod. M-V100008016I stainless M8x16 hexagonal head screw
motors.
14
interference.