Publicité
Les langues disponibles
Les langues disponibles
3) GUARD FUNCTION
a) Check guard for proper closing before each use. Do
not operate the saw if guard does not move freely
and enclose the blade instantly. Never clamp or
tie the guard so that the blade is exposed. If saw is
accidentally dropped, guard may be bent. Check to make
sure that guard moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
b) Check the operation and condition of the guard
return spring. If the guard and the spring are not
operating properly, they must be serviced before
use. Guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
c) Assure that the base plate of the saw will not shift
while performing the "plunge cut" when the blade
bevel setting is not at 90°. Blade shifting sideways will
cause binding and likely kickback.
d) Always observe that the guard is covering the
blade before placing saw down on bench or floor.
An unprotected, coasting blade will cause the saw to
walk backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch is
released.
ADDITIONAL SAFETY WARNINGS
GENERAL
•
This tool is not intended for use by children and persons
with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of
the tool by a person responsible for their safety
•
Before using the tool for the first time, it is recommended
to receive practical information
•
This tool is not suitable for wet cutting 3
•
Always disconnect plug from power source before
making any adjustment or changing any accessory
•
Never use the tool for side grinding
•
Never use the tool when the cord is damaged; it must be
replaced by a specially prepared cord available through
the service organization.
•
Do not operate the power tool stationary (it is not
designed for operation with a saw table)
•
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
•
Do not saw ferrous metals (red hot chips can ignite the
dust extraction)
•
When working stone, use dust extraction; the
vacuum cleaner must be approved for the extraction
of stone dust (using this equipment reduces dust-
related hazards)
•
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
Follow the dust-related national requirements for the
•
materials you want to work with
ACCESSORIES
•
SKIL can assure flawless functioning of the tool only
when original accessories are used
•
Use only saw blades that correspond with the
characteristic data given in these operation instructions
and that are tested and marked in accordance with EN
847-1
•
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
•
Use only saw blades/cut-off wheels with a minimum
diameter of 85 mm, a maximum diameter of 89 mm
and a spindle hole of 10 mm
•
Never use grinding discs with this tool
•
Handle and store accessories with care
BEFORE USE
•
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
•
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
•
Be familiar with the controls and the proper use of the
tool
•
Remove all obstacles on top of as well as underneath the
cutting path before you start cutting
•
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
•
Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
•
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
•
The noise level when working can exceed 85 dB(A); wear
ear protection
•
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
•
Never use the tool without the original protection guard
system
•
Do not attempt to cut extremely small workpieces
•
Do not work overhead with the power tool (sufficient
control of the power tool is not ensured in this working
manner)
•
In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
•
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
•
After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
EXPLANATION OF SYMBOLS ON TOOL
4 Read the instruction manual before use
5 Double insulation (no earth wire required)
6 Wear protective glasses and hearing protection
7 Do not dispose of the tool together with household waste
material
13
Publicité
