WMF KUCHENMINIS Mode D'emploi page 11

Pulse function
To use the pulse function, select PULSE on the speed controller (10).
The motor operates at maximum speed while the speed controller (10) is set to
the pulse function. The maximum runtime must not exceed one minute.
Planetary mixing system
The planetary mixing system ensures that the ingredients are mixed thoroughly
and evenly. This prevents ingredients/dough from sticking to the edge.
Soft-start
The soft-start function always starts the appliance at a low speed, irrespective of
the selected speed. The speed gradually increases until it has reached the required
setting. This prevents ingredients spraying out.
Electronic speed regulator
The appliance is equipped with an electronic speed regulator that serves to keep
the speed constant under different loads.
Timer function
The timer function can be used with or without the appliance's other functions
to, e.g. set the exact time for the dough to rise. If you activate the timer function,
you can continue using the other functions on the appliance.
Note: The timer function can only be activated when the speed controller (10) is
in the Off position (0).
▪ Press the Start/Pause button or the Plus/Minus buttons to turn on the display.
(Fig. F). The LCD lights up white and shows the preset time "00."
▪ Press the Plus/Minus buttons to set the desired time. The time can be set in
one-minute increments up to 99 minutes.
F
Note: The time can also be changed when the timer is activated, by pressing the
Plus/Minus buttons.
▪ Press the Start/Pause button to activate the timer function. The
appears on the LCD and the remaining time is shown.
▪ Once the time has elapsed, the appliance beeps and the timer function
switches off.
Note: Hold the Start/Pause button pressed down for at least three seconds to
reset the timer. "00" appears on the display.
Note: The LCD switches off automatically after one hour if you do not press the
Start/Pause button, Plus/Minus buttons or the speed controller. This resets the
timer.
Pausing the timer function
The timer function can be "paused" at any time.
▪ Press the Start/Pause button to "pause" the time. The
▪ To reactivate the timer function, press the Start/Pause button. The
stops flashing.
Timer function and automatic switch-off
When using the timer function together with the automatic switch-off, the
appliance stops automatically when the preset time has elapsed.
▪ Set the desired time as described in the "Timer function" section.
▪ Start the timer function by selecting a speed setting on the speed controller.
G
(Fig. G) The LED ring lights up white. The
the remaining time is shown.
20
icon
icon starts to flash.
icon
icon appears on the display and
Note: The timer does not work with the "Pulse" function.
Note: The time can also be changed when the timer is activated, by pressing the
Plus/Minus buttons.
▪ Once the time has elapsed, the appliance beeps and switches off
automatically. The LED ring on the speed controller flashes until you turn it to
the Off position (0).
Note: Hold the Start/Pause button pressed down for at least three seconds to
reset the timer. "00" appears on the display.
Note: The LCD switches off automatically after one hour if you do not press the
Start/Pause button, Plus/Minus buttons or the speed controller. This resets the
timer.
Pausing the timer function with the automatic switch-off
The timer function can be "paused" at any time.
▪ Set the speed controller to the Off position (0) to "pause" the time. The
icon starts to flash.
▪ Select the desired speed setting again using the speed controller to reactivate
the timer function. The icon stops flashing.
Note: To reactivate the timer, the speed controller must be in the Off position (0).
Note: During operation and when the timer is activated, the timer pauses if the
mixer cover or front cover is removed or the mixer arm is opened. The (Image)
icon and LED ring flash. The timer starts again once the covers have been replaced
and the mixer arm has been locked into position or the speed controller is moved
to the Off position (0) once and back to the required speed setting.
Splash guard (9)
▪ The splash guard (9) prevents splashing during mixing. The filler opening on
the splash guard (9) can also be used to add further ingredients directly while
mixing.
▪ Press the release button to tilt the mixer arm upwards.
Note: The mixer accessories (flat beater, dough hook and whisk) must be
removed before inserting the splash guard (9).
▪ Insert the splash guard (9) into the mixer arm holder from underneath with
H
the filler opening facing upwards.
▪ Turn the splash guard (9) in a clockwise direction until it locks into place.
Note: The splash guard (9) can be used in three different positions (Figs. H-J).
▪ Push the required mixer accessory (flat beater, kneading hook or whisk) into
the attachment as far as it will go and rotate it anticlockwise until it locks
into place.
I
▪ Lower the mixer arm.
▪ The splash guard (9) does not need to be removed to detach the mixer
accessories.
▪ To remove the splash guard (9), set the speed controller to the Off position (0)
and lift the mixer arm. Turn the splash guard (9) in an anticlockwise direction
J
and pull it downwards.
21