Vimar Elvox RS17.P Guide Rapide Installateur page 7

RS17.P
Time setting
The control panel is programmed by default with the following times:
- automatic closing: 30 s
- offset for opening: 3 s
- offset for closing: 6 s
To change the default times, follow the procedure below (the phases for installing a double swing leaf gate have a grey background; if there is a single
leaf, the leaf offsets are not programmed)
The control panel does not need travel setting as this is automatically measured with each action. For this to happen, run a complete open-close action
(it will take place at reduced speed as the control panel does not know the exact position of the leafs).
NOTE: In order to perform this procedure, the gate must be stationary.
CAUTION! THE SAFETY DEVICES ARE DISABLED WHILE CARRYING OUT THIS PROCEDURE..
Pressing
No. Phase
push button
1 PROG Procedure activation
2 - Leaf closing
3 - Opening M1
4 51 Setting the offset for opening
5 - Completion of opening
6 51 Setting the pause time
7 - Closing M2
8 51 Setting the offset for closing
M1 starts closing
9 - Completion of closure and end of
programming
Note:
If you want to return the control panel to default, perform the following procedure:
1. Disconnect the power to the control panel
2. Press and hold the PROG button.
3. Reconnect the power to the control panel and wait for the flashing light to come on steady.
4. After 3 sec., release the PROG button. The flashing light will turn off.
5. The control panel is now set with the default times.
Remote control programming
Note: Remote control programming can only be done with the automatic gate system stationary
Step-by-step programming:
No. Pressing push button
1
MRX
2 MRX+ remote control
3 -
Programming the pedestrian:
No. Pressing push button
1 MRX+PROG
2 MRX+PROG+remote control -
3
-
Deleting a remote control
No. Pressing push button
1 MRX
2
MRX+ remote control
3 -
Complete deletion of the receiver
No. Pressing push button
1
MRX
2 -
Note:
After deleting all the remote controls, the first saved remote control configures the control panel to accept only remote controls with a rolling
code or only remote controls with a fixed code.
VIMAR group
Description
Press and hold down the PROG push button until the flashing light comes on steady, then release
the button, and the automatic gate system will now close the gate.
Unless the leafs are already closed, the first action MUST be CLOSING; otherwise, cut off
the power supply to the control panel and invert the cables of the motor that opens instead
of closing.
N.B. DO NOT INVERT THE ENCODER CABLES.
M1 starts to open and the control panel starts the count of the offset for opening
After the desired time, press and release button 51 to set the offset for opening (if not
pressed, after 40 s M2 will start automatically). M2 starts opening
M1 and M2 continue to open at low speed until they reach the mechanical stops on opening
With the gate stationary in the fully open position, the automatic closing time count starts,
after the required length of time has passed, press and release push button 51, the control
panel will save the elapsed time (max. 250 seconds)
M2 starts to close and the control panel starts the count of the offset for closing
After the desired time, press and release button 51 to set the offset for closing (if not pres-
sed, after 130 s M1 will start automatically).
The automation completes the closure when it reaches the closing mechanical stops and the
flashing light goes out to signal that the travel programming procedure has been exited.
Signal
Description
MRX LED
Off Press and hold down the MRX push button for no more than 7 s
- With the MRX push button still pressed, press the button of the remote control to be saved
1 blink Button of the saved remote control (new remote control)
2 blinks Button of the saved remote control (remote control already in memory)
Signal
Description
MRX LED
Off Press and hold down the MRX and PROG push buttons for no more than 7 s
With the MRX and PROG push buttons still pressed, press the button of the remote control to be saved
1 blink Button of the saved remote control (new remote control)
2 blinks Button of the saved remote control (remote control already in memory)
Signal
Description
MRX LED
On steady Press and hold down the MRX push button for at least 7 s until the MRX LED comes on steady
- With the MRX push button still pressed, press the button of the remote control to be deleted
3 blinks Deletion successful
MRX LED indi-
Description
cator
Flashing light Press and hold down the MRX push button for at least 14 s until the MRX LED starts flashing
10 blinks Complete deletion of the receiver
EN
5