Yamaha MG206C Mode D'emploi page 21

Table des Matières

Publicité

Reference
Specifications
MG206C
■ Electrical Specifications
Frequency Response
MONITOR OUT, REC OUT
Total Harmonic Distor-
tion (THD + N)
Hum & Noise
Hum & Noise are mea-
sured with a 6
dB/octave filter @ 12.7
kHz; equivalent to a 20
kHz filter with infinite
dB/octave attenuation.
Crosstalk (1 kHz)
Maximum voltage gain
(1 kHz)
INPUT GAIN: maximum
All faders and controls
are maximum when
measured.
PAN/BAL: panned
hard left or hard right
Phantom Voltage
■ General Specifications
Input HPF
Input equalization
±15 dB maximum
Turn over/roll-off frequency of
shelving: 3 dB blow maximum
variable level.
PEAK Indicator
LED Level Meter
Power Supply Adaptor
Power Consumption
Dimensions (W x H x D)
Net Weight
All faders are nominal if not specified.
Output impedance of signal generator: 150 ohms
STEREO OUT GAIN: min (CHs 1–19/20)
20 Hz–20 kHz
GROUP OUT
Nominal output level @1 kHz
AUX SEND
Input: CHs 1 to 19/20, RETURN, 2TR IN
STEREO OUT +14 dBu @ 20 Hz–20 kHz, Input GAIN Control at minimum
CH INPUT 1–12 MIC EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN: maximum
STEREO OUT STEREO OUT, GROUP 1-2 fader and GROUP 3-4 fader at
nominal level and all channels' ST and 1-2, 3-4 switches off.
GROUP OUT
AUX SEND Master/AUX control at nominal level and all CH AUX controls at
minimum.
STEREO OUT STEREO OUT, GROUP 1-2, GROUP 3-4 faders and one CH
fader at nominal level.
GROUP OUT
STEREO OUT Residual Output Noise
Adjacent Input CHs 1–12
Input to Output STEREO L/R, CHs 1–12, PAN: panned hard left or right
Rs = 150 Ω
MIC to CH INSERT OUT
MIC to STEREO OUT
MIC to GROUP OUT
MIC to GROUP to ST
MIC to REC OUT
MIC to MONITOR OUT, ST TO MONITOR
MIC to PHONES OUT
MIC to AUX SEND PRE
MIC to AUX SEND POST
CH 17/18, 19/20 LINE to STEREO OUT
CH 17/18, 19/20 LINE to GROUP OUT
CH 17/18, 19/20 LINE to AUX SEND PRE
CH 17/18, 19/20 LINE to AUX SEND POST
Rs = 150 Ω RETURN to STEREO OUT
RETURN to AUX SEND
Rs = 600 Ω 2TR IN to STEREO OUT
MIC no load
80 Hz, 12 dB/oct
CHs 1–12 HIGH: 10 kHz (shelving)
MID: 250 Hz–5 kHz (peaking)
LOW: 100 Hz (shelving)
CH 13/14–19/20 HIGH: 10 kHz (shelving)
MID: 2.5 kHz (peaking)
LOW: 100 Hz (shelving)
Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for
CHs 13/14–19/20) reaches -3 dB below clipping (+17 dBu).
Pre MONITOR Level
2x12 points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB)
STEREO/GROUP/PFL bus
PEAK lights if the signal level reaches 3 dB below the clipping level.
PA-30 AC 35 VCT, 1.4 A, Cable Length = 3.6 m
40 W
478 mm x 102 mm x 496 mm
6.0 kg
MG206C/MG166CX/MG166C Owner's Manual
MIN
TYP MAX UNIT
-3.0
0.0
1.0
dB
0.1
%
-128
-88
-81
dBu
-64
-98
-70
dB
-70
60
84
94
62.2
94
83
76
dB
86
58
47
57
16
9
27.8
48
V
75

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Mg166cxMg166c

Table des Matières