CDV Group DIGIWAY DWS102 Serie Manuel D'installation Et Utilisation page 17

General safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.17
Machinery Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.18
Identifying products and parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.19
Identifying accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.20
Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.21
Overall dimensions and mounting quotes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.22
Installation - Sliding arm version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.23
Installation - Articulated arm version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.24
Complete wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.25
Connection table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.26
Setting and adjiusting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.27
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.28
Functionalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.28
Actuation force adjust. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.29
Disable persons configuration and requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.30
Remote controls management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.30
Door trip adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.31
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pag.47
General safety precautions
This manual is intended for professional competent personnel adeguately trained.
Installation and connections must be realized in accordance with Good Working methods and in compliance with the
current Regulations. Bad installing could be sourse of hazard.
Read carefully this manual before commencing the installation.
Check first of all the existing structure : verify its integrity, stability and strenght.
If it's necessary do all the structural modifications in order to make it standard, keeping present all the possible
deformations which could occur during the normal use.
Verify that all the zones where exists risk of crushing, dragging, shearing and other dangers, are protected by
electronic safety, safety freeboards or barriers.
These devices must be installed in compliance with the current laws and in a perfectly workmanlike way, also in
relation to the place of use, the type of use and the operating logic of the product.
The forces developed by the complete system must comply with the current standards and, where this is not possible,
protect the zones with electronic safety devices.
Apply hazads area notices required by applicable regulations.
Before the actuator is connected, make sure that the plate details corresponds to those of the power mains and that
there is a differential circuit-breaker and an adeguate protection against overcurrents on the supply side of the
system.
Fit an omnipolar disconnection switch with contact opening gap of at least of 3 mm.
Interrupt the power supply before opening the cover of the actuator for any maintenance or repairing intervention.
The handle of electronic parts must be effected wearing grounded antistatic bracelets to avoid any static damage.
Servicing the actuator is of fundamental importance if the system is to operate correctly and safely.
Comply with the manufacturer's instructions described in this manual.
Only use genuine spare parts if replacements or repairs are required.
The motor manufacturer declines any responsability in the event of component parts fitted that are not compatible with
the safe and correct operation.
The actuator must be installed only inside buildings
The manufacturer declines all liability for damage caused by assembly on the outside, without adequate protections.
This product cannot be installed in places with an explosive atmosphere or in the presence of inflammable fumes or
gases.
Summary
A CDV Group product
UK
Pag.17