Connections; Controls & Connectors - Yamaha TSS-1 Mode D'emploi

Masquer les pouces Voir aussi pour TSS-1:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
1
(See figure
inside the front cover.)
Caution: Plug in the amplifier unit and other
equipment after all connections are
completed.
A : Connect the three satellite speakers with a 3 m cord to
the FRONT L, R and CENTER terminals. Connect the
two satellite speakers with a 7 m cord to the
SURROUND L and R terminals. Connect the
subwoofer to the SUBWOOFER terminal.
B : Connect external audio/video units (a personal
computer, a video game player, a portable DVD/CD
player, a video cassette player, etc. which send
playback signals to this system) to these terminals.
2
(See figure
inside the front cover.)
1
INPUT selector button and indicators
Press this button repeatedly to select an input mode
between DIGITAL, 4CH and 2CH. The current mode is
shown by the lighting of the corresponding indicator.
DIGITAL:
Select this mode to reproduce signals received at the
OPTICAL or the COAXIAL terminal on the rear panel.
When both OPTICAL and COAXIAL terminals receive
signals, the signals at the OPTICAL terminal are
selected.
4CH:
Select this mode to reproduce signals received at the
analog input FRONT and SURROUND terminals on
the rear panel in 4-channel surround sound mode. (The
center speaker is not used in this mode.)
2CH:
Select this mode to reproduce signals received at the
analog input FRONT terminal on the rear panel. (The
PROLOGIC surround mode can be used in this
mode.)
2
MODE selector button and indicators
Press this button repeatedly to select the desired
surround mode between on (DTS,
PROLOGIC) and off. The current mode is shown by
the lighting of the corresponding indicator.
* If a DTS or Dolby Digital encoded signal is inputted
when the surround mode is off, the corresponding
indicator lights up dimly.
DTS:
Select this mode to reproduce a DTS encoded input
source.
This mode can be selected only when the input signal
is encoded with DTS and the input mode is set to
DIGITAL.
6
E-

Connections

Cautions
● When placing the provided AC adaptor on the desk, etc.,
● The SPEAKER OUTPUT terminals on the rear of the
Controls & connectors
3
DIGITAL,
4
5
be sure to fix the adaptor on the desk, etc. to prevent it
from falling. If the adaptor falls, it may cause personal
injury or damage to the adaptor and/or other equipment.
amplifier unit are only designed for connection of the
supplied speakers. Never connect these terminals to an AV
amplifier or a power amplifier, as it may cause
misoperation, fire and/or damage to this system.
DIGITAL:
Select this mode to reproduce a Dolby Digital encoded
input source.
This mode can be selected only when the input signal
is encoded with Dolby Digital and the input mode is set
to DIGITAL.
PROLOGIC:
Select this mode to reproduce a Dolby Prologic
encoded input source.
This mode cannot be selected when the input mode is
set to 4CH.
TEST button
Press this button to reproduce a test tone from the
speakers. A test tone is reproduced from each speaker
as shown below. The test tone is used for adjusting
volume balance among all the speakers.
FRONT L
CENTER
SURROUND L
* Not all of the speakers reproduce the test tone
depending on the setting of the SPEAKER MODE
C
switch (
).
MUTE button and indicator
Press this button to cut off sound output temporarily.
When this function is active, the indicator lights up.
Press this button again to restore sound output.
* Sound output will also be restored by changing the
status of this system between standby and power-on
modes, and changing the input mode or the surround
mode.
CENTER level control
This control is used for adjusting the sound level from
the center speaker. Turn this control clockwise to
increase the level, and counterclockwise to decrease
the level.
FRONT R
SURROUND R

Publicité

Table des Matières
loading

Table des Matières