Table des Matières
Publicité
Liens rapides
INSTALLATION AND
OPERATION, MANUAL
THE GARLAND
GAS XPRESS GRILL,
MODELS XG24, XG36
FOR YOUR SAFETY:
DO NOT STORE OR USE GASOLINE
OR OTHER FLAMMABLE VAPORS OR
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
WARNING:
IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY,
OR DEATH. READ THE INSTALLATION,
OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY
BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT
Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent
using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been
improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation
instructions provided with the product, or any product that has its serial number defaced, obliterated or removed,
or which has been modified or repaired using unauthorized parts or by unauthorized service agents.
For a list of authorized service agents, please refer to the Garland web site at http://www.garland-group.com.
The information contained herein, (including design and parts specifications), may be superseded and is subject
to change without notice.
GARLAND COMMERCIAL RANGES, LTD.
1177 Kamato Road, Mississauga, Ontario L4W 1X4
CANADA
Phone: 905-624-0260
Fax: 905-624-5669
Part # 4517124 Rev. 7 (08/17/11)
APPLIANCE
PLEASE READ ALL SECTIONS OF THIS MANUAL
AND RETAIN FOR FUTURE REFERENCE.
THIS PRODUCT HAS BEEN CERTIFIED AS
COMMERCIAL COOKING EQUIPMENT AND
MUST BE INSTALLED BY PROFESSIONAL
PERSONNEL AS SPECIFIED.
IN THE COMMONWEALTH OF MASSACHUSETTS
THIS PRODUCT MUST BE INSTALLED BY A
LICENSED PLUMBER OR GAS FITTER. APPROVAL
NUMBER: G-1-07-05-28
For Your Safety:
Post in a prominent location, instructions to be
followed in the event the user smells gas. This
information shall be obtained by consulting
your local gas supplier.
© 2005 Garland Commercial Industries, Inc.
Publicité
Table des Matières
Manuels Connexes pour Garland XG24
Sommaire des Matières pour Garland XG24
- Page 1 Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation instructions provided with the product, or any product that has its serial number defaced, obliterated or removed, or which has been modified or repaired using unauthorized parts or by unauthorized service agents.
-
Page 2: Introduction
INTRODUCTION The Garland Xpress Grill provides a method for efficient two-sided cooking, while accommodating a variety of products. The unit will also serve as a flat grill, and meets all standards for safety, efficiency, and cleanliness. Standard Features: • Stainless steel front, top & sides •... -
Page 3: Table Des Matières
Gas Connections and Pipe Sizing ..... . . 7 To View the Garland Part Number: ..... 23 Appliances Equipped with Casters: . - Page 4 DIMENSIONS & SPECIFICATIONS, XG24 26-23/32" [678mm] FROM PLATEN 25-1/2" ARM PIVOT [646mm] AVERAGE 11-1/2" [292mm] 4-41/64" ÉLÉMENT CHAUFFANT [118mm] 28-3/16" SUPÉRIEUR 23" [716mm] [584mm] (2 ENDROITS) 44.03° TOP VIEW 50-1/2" AVERAGE [1282mm] [48° MAX] 2-3/4" AVERAGE [70mm] 1-23/32" [44mm] 24"...
-
Page 5: Operating
Crated Uncrated Sides Rear BTU/Hr 47-1/2" 40-3/4" 6" 3" 7.0" WC 11.0" WC 3.5" WC 3.5" WC 99,000 29.1 (1207mm) (1035mm) (152mm) (76mm) Form# XG36 (08/24/10) Part # 4517124 Rev. 7 (08/17/11) Page 5 Garland Commercial Ranges Ltd 1177 Kamato Road, Mississauga, Ontario L4W 1X4 CANADA... -
Page 6: Safety Precautions
Xpress Grill unless all main power supplies to the grill access panels are in place and fastened properly. have been disconnected. The Garland Xpress Grill is a semi-automatic cooking • USE EXTREME CAUTION in setting up, operating and appliance. The upper platen is lowered automatically,... -
Page 7: National Codes Requirements
INSTALLATION continued Gas Connections, and Pipe Sizing: Grill is to be located directly under ventilation system. Once installed in the grill station underneath the ventilation The size of the gas line is very important. If the line is too system, the platens, in their highest position, must not small, the gas pressure at the burner manifold will be low. -
Page 8: Appliances Equipped With Casters
INSTALLATION continued Appliances Equipped with Casters: 1. The installation shall be made with a connector that complies with the Standard for Connectors for Moveable Gas Appliances, ANSI Z21.69 or latest edition, addenda Z21.69a-1989, and a quick-disconnect device that complies with the Standard for Quick Disconnects for Use with Gas Fuel. -
Page 9: Grill Controls
GRILL CONTROLS WHEN PUSHED SIMULTANEOUSLY: "START COOK TIME COUNTDOWN" (flat grill cooking) OR "LOWER PLATEN" (two-sided cooking) 16-CHARACTER INDICATORS 2-LINE DISPLAY CANCEL/ RAISE PLATEN BUTTON PRODUCT MASTER BUTTONS POWER SWITCH POWER ENTER BUTTON BUTTON PROGRAM DOWN ARROW BUTTON BUTTON TEMPERATURE UP ARROW BUTTON BUTTON... -
Page 10: Temperature Button
GRILL CONTROLS continued Temperature Button: Enter Button: In the Cook mode, each time the button is pressed the Function is to accept programming steps. current temperature for one zone is displayed. The grill Cancel/Raise Platen Button, (Green): temperature is displayed first followed by the platen temperature. -
Page 11: Operation
OPERATION Installing Release Material: RELEASE MATERIAL A release material sheet must be replaced when: RELEASE MATERIAL • Product sticks to release material. LOCKING CLIP (1) • Carbon build-up ruins taste or appearance. • Tearing occurs in the sheet’s cooking area. • Release material coating is worn off sheet. Slide release material rod through hemmed end of the release material sheet. -
Page 12: Simplified Cook Cycle Instructions
Press both green and black butto Place item on grill surface and select item number for that item to to lower clam and begin cooking OPERATION continued product. be cooked. Clam Grill Operating Instructions Simplified Cook Cycle Instructions: 5. Press green button to cancel any time during cook cycle. 1. -
Page 13: To Cook In Flat Grill Mode
OPERATION continued To Cook in Flat Grill Mode: Enter Standby Mode: 1. To start a cook cycle select a product recipe by using the Stand by mode is used during slow periods to conserve product keys (1 through 9) or by using the UP/DOWN energy with out a complete shut down of the unit. -
Page 14: Platen Set
OPERATION continued EXTENDED TIME: 3. Press the ENTER key to initiate the clean mode. This option will add 6, 4 and 2 seconds to the time of the next 4. The display SHOWS the message “READY TO CLEAN” with three cooks respectively if the grill has had no activity for flashing in the second line when the actual temperature 5 minutes. - Page 15 CLEANING AND MAINTENANCE continued • Select Clean Mode • Remove the locking clips, • Scrape the lower grill • Wipe the Release When Clean Mode has bars, and release sheets. surface with the scraper. Material sheets with a Wash, rinse, and set aside been reached, the LED clean,sanitizer-soaked •...
- Page 16 CLEANING AND MAINTENANCE continued • Rinse the edges of all three • Place upper platen • Rinse both sides of • Pour a small amount of platens. release material sheets the release material lukewarm water on a fl at on the lower grill sheets with a clean, clean, sanitizer-soaked •...
-
Page 17: Accessories
PLATEN ZEROING Cancel (Green) button to raise the platen. Now, press both 11. Next go to the left rear adjuster and raise the platen until the Cancel (Green) and (Black) Buttons to re-lower the the gapping tool fits snugly between the upper platen platen. - Page 18 ACCESSORIES Grill Squeegee - 1868201 Platen Gapping Tool -1838701 “No-Go” “Go” Insert gap tool directly below platen adjusters. Page 18 Part # 4517124 Rev. 7 (08/17/11)
- Page 19 PLATEN ZEROING continued Platen Adjusting Tool - 4523323 Platen leveling should be done from one corner to the opposite corner. The adjuster nuts should be turned opposite of one another. Use this end to turn all slotted adjuster caps and nuts Platen Adjuster Cap - 1859102 Platen Adj Lock Nut - 1859103 Shoulder Bolt - 8005401...
-
Page 20: Programming
PROGRAMMING Programming Modes/Menu Sequence: System Information Page 20 Part # 4517124 Rev. 7 (08/17/11) - Page 21 PROGRAMMING continued System Set-up UPPER SET TEMP GRILL SET TEMP Service Mode PLATEN GAP SET Part # 4517124 Rev. 7 (08/17/11) Page 21...
-
Page 22: Menu Items
PROGRAMMING continued Menu Items... 5. Use to choose the desired Menu Item. To Change the Cook Time of a Product: 6 Press three, (3) times to display “(MENU ITEM) UPPER TEMP XXX” displayed in °F or °C. 1. Press and hold for three, (3) seconds. -
Page 23: To Change Product Button, "Key" Assignment
SYSTEM INFO. ” 8. Press to save the changes. You will automatically 5. Press three, (3), times to view the Garland Part Number return to “PROGRAMMING MODE MENU ITEMS”. for the grill. “GARLAND PART # X…X” is displayed. (number varies by grill). -
Page 24: To View The Flash Number
PROGRAMMING continued To View the Flash Number: number varies by grill). 6. Press to return to “PROGRAMMING MODE SYSTEM 1. Press and hold for three, (3) seconds. “ENTER CODE” is INFO”. displayed. 7. Press to exit. 2. Using the Product buttons, 0-9 enter the code, (1251). “ENTER CODE **** ”... -
Page 25: To Change The Alarm Volume
PROGRAMMING continued To Change the Alarm Volume: 3. Press to enter the Programming Mode. “PROGRAMMING MODE MENU ITEMS” is displayed. 1. Press and hold for three, (3) seconds. “ENTER CODE” is displayed. 4. Press two, (2) times. “PROGRAMMING MODE SYSTEM SETUP”... -
Page 26: To Change Probe Calibration - Grill
PROGRAMMING continued 2. Using the Product buttons, 0-9 enter the code, (1251). 5. Press five, (5), times. “PROBE CAL – UPPER XXXF” is “ENTER CODE **** ” is displayed. displayed. 3. Press to enter the Programming Mode. 6. Use to change the Probe Calibration to the “PROGRAMMING MODE MENU ITEMS”... -
Page 27: To Turn Extended Time On/Off
PROGRAMMING continued “PROGRAMMING MODE MENU ITEMS” is displayed. Clamshell mode. 4. Press two, (2) times. “PROGRAMMING MODE SYSTEM 7. Press to save the changes. SETUP” is displayed. 8. Press to return to “PROGRAMMING MODE MENU 5. Press eleven, (11) times. “CONTROL TYPE ELECTRIC (or ITEMS”... -
Page 28: To Turn Clean Mode On/Off
PROGRAMMING continued LIB” is displayed. 8. Press to return to “PROGRAMMING MODE MENU ITEMS” 10. Press to exit. 9. Press again to exit. To Modify a Product Name in Library: To Turn Clean Mode On/Off: 1. Press and hold for three, (3) seconds. “ENTER CODE” is displayed. -
Page 29: To Perform Limit Switch Test
PROGRAMMING continued 9. Press again to exit. 5. Press two, (2), times. “PLATEN” (along with the position of each switch), is displayed. To Perform Limit Switch Test: 6. Use to move the platen up and down. Check 1. Press and hold for three, (3) seconds. - Page 30 5.75" 5.75" 5.75" 22.5" 22.5" 11.25" 11.25" PLATEN PLATEN (2 PLACES) (3 PLACES) GRILL PLATE GRILL PLATE 24" 24" 12" 12" 6.09" 6.09" 6.09" 6.09" 18" 24" 36" MODEL XG24 MODEL XG36 Page 30 Part # 4517124 Rev. 7 (08/17/11)
-
Page 31: Error Logic & Troubleshooting
ERROR LOGIC & TROUBLESHOOTING Probe Error Heating Error Occurs when the probe Occurs the controller is open or not connected. will fails to detect a The controller will turn temperature response the heat off. over a 6-minute period. Grill & Grill & Grill Platen Grill Platen Platen Platen Heating Heating Probe Error Probe Error Probe Heating Error Error Errors Errors Grill is Grill is Grill Grill Grill Grill operable operable is not... -
Page 32: Platen Down Error
ERROR LOGIC & TROUBLESHOOTING continued Platen Down Error Gas Ignition Error Motor Overcurrent Error Occurs when current to the motor Occurs at cycle-start when the Occurs when the ignition exceeds 4.8 amps, typically because platen fails to reach lower limit feedback signal does not platen movement has encountered position within 40 sec. respond after 4 tries. mechanical resistance L1: PLATEN DOWN L1: IGNITION ERROR L1: MOTOR L2: OVERCURRENT Audio Alarm Audio Alarm Audio Alarm Error Error Error... -
Page 33: Motor Error2
ERROR LOGIC & TROUBLESHOOTING continued Motor Error2 Lower Switch Error Upper Switch Error Occurs when the platen is in motion Occurs at cycle start when the Appears in code, and fails to reach the upper or lower lower limit switch fails to signal the but is never set. limit position within 30 seconds, platen’s arrival at the lower limit (150 encoder counts) position within 200 seconds. L1: MOTOR L1: LOWER SWITCH L1: UPPER SWITCH L2: ERROR2 L2: FAIL L2: FAIL Audio Alarm Audio Alarm Audio Alarm Recycle Main Recycle Main... -
Page 34: Wiring Diagram
WIRING DIAGRAMS 1333W Page 34 Part # 4517124 Rev. 7 (08/17/11) - Page 35 WIRING DIAGRAMS 1333W Part # 4517124 Rev. 7 (08/17/11) Page 35...
- Page 36 WIRING DIAGRAMS Page 36 Part # 4517124 Rev. 7 (08/17/11)
- Page 37 WIRING DIAGRAMS Part # 4517124 Rev. 7 (08/17/11) Page 37...
- Page 38 Page 38 Part # 4517124 Rev. 7 (08/17/11)
- Page 39 Part # 4517124 Rev. 7 (08/17/11) Page 39...
- Page 45 MAIN SWITCH 240V 120V PLATEN RED PLATEN YELL GRIDDLE RED GRIDDLE YELLOW MOTOR ACTUATOR...
- Page 46 MAIN SWITCH 240V 120V PLATEN RED PLATEN YELL GRIDDLE RED GRIDDLE YELLOW MOTOR ACTUATOR...