Using The Dehumidifier; Dehumidification Mode - Wood's MDX14 Guide D'instructions

Masquer les pouces Voir aussi pour MDX14:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 50
Operating Instructions
GB
PLACEMENT OF DEHUMIDIFIER
- The dehumidifier should not be placed
near radiators or other heat sources or
exposed to direct sunlight, as it will reduce
performance.
- Ideal is to put it in the centre
of the room / area.
NOTE: When placed in a shower
room or bathing area, the dehumidifier
should be fixed in place. It is
compulsory to check and respect your
local bathroom electrical regulations
before use.

USING THE DEHUMIDIFIER

If the dehumidifier is transported
horizontally, let the dehumidifier stand
for 4 hours before being used. It is very
important that the oil runs back into the
compressor, otherwise, the dehumidifier
may be seriously damaged.
1. Check that the water reservoir is correctly
placed.
2. Connect the dehumidifier to a grounded
power source.
3. Set the function or desired humidity level.
See the section on the humidity control.
OPERATION MANUAL
1.
Power Button: This button can control
the machine on and off.
2.
Mode Button: Press to select the
desired mode. It can switch to Normal
dehumidification, Eco
dehumidification, Auto dehumidi-
fication, Ventilation mode, and Dry
clothes mode.
ECO MODE
When the unit works at ECO MODE, the
default humidity level is RH60%.
a) When the ambient humidity ≥ 60%, the
12
unit will work as dehumidification, the fan
speed is not adjustable.
b) When the ambient humidity<60%,
the unit will work as a fan and the speed
is not adjustable.
c) The humidity level is not adjustable.
FAN MODE
Under this mode, the compressor is not
engaged. By default, the adjustable fan
speed is set to "low", for ventilation only.
The humidity level cannot be set, but the
ambient humidity level (30-90%RH) is
indicated on display panel.
DRY MODE
Under this mode, the compressor will
continuously run, as will the fan at high
speed regardless of room humidity. Three
minutes delay protection function of the
compressor is applicable. The fan speed
and humidity level cannot be adjusted.
Ambient humidity level (30-90%RH) will be
indicated on the display panel.
AUTO MODE
When the unit works on AUTO MODE, the
default humidity level is RH50%
a) When the ambient humidity ≥ 70%, the
unit will work as strong dehumidification,
the fan speed is not adjustable.
b) When 50% ≤ the ambient
humidity<70%, the unit will work as weak
dehumidification, the fan speed is not
adjustable.
c) When the ambient humidity<50%, the
unit will work as a fan in low speed with
the fan speed not being adjustable.
d) The ambient humidity level (30-
90%RH) will be indicated on the display
panel, and the humidity is not adjustable.

DEHUMIDIFICATION MODE

The unit will work at dehumidification
mode when power-on for the first time
or choose by mode conversion, the fan
speed is defaulted high, press UP and
DOWN to adjust the setting humidity (35-
85%).
3.
Humidity can be set between 35%
-85% (5% adjustment factor);
humidity setting is only valid under
dehumidification mode.
4.
Timer: You can set how long the unit
will run or when it will start. You can
select 1-24 hours.
5.
Fan Speed: The speed key is valid
only in dehumidification mode and
ventilation mode.
6.
Child-lock: Press both "Timer" and
"Speed" to set or shut off the Child-
lock function.
WATER DRAINAGE
When the water reservoir is full, the
dehumidifier will shut off automatically.
1.
Disconnect the dehumidifier from the
power source.
2.
Empty the water reservoir.
3.
Put the empty water reservoir back
and check that the float moves freely.
4.
Connect the dehumidifier to the
power source.
Direct water drainage
Connect a water hose to the pipe on the
back of the dehumidifier. Lead the other
end to a drain. Make sure that the water
can be drained downwards by gravity.
AIR FILTER
The air filter prevents dust and dirt from
entering the machine, prolonging its life
expectancy. The filter must be cleaned
regularly.
Filter cleaning:
1.
Remove the filter.
2.
Wash it with warm water and a mild
cleansing agent. Alternatively, the
filter may be vacuum cleaned.
3.
Let the filter dry and put it back.

Publicité

Table des Matières
loading

Table des Matières