LOVATO ELECTRIC DMG700 Manuel D'application page 11

M02 - UTILITY
P02.01 Language
P02.02 Display contrast
P02.03 High backlight level
P02.04 Low backlight level
P02.05 Low backlight delay
P02.06 Default page return
P02.07 Default page
P02.08 Default sub-page
P02.09 Display update time
P02.06 – If set to OFF the display always remains in the page where the user left it. If set to a time delay, after that time the display page goes back to page set in P02.07.
P02.07 – Number of the page to which the display returns automatically after time specified by P02.06 has elapsed from the last keystroke.
P02.08 – Sub-page type to which the display returns after P02.06 has elapsed.
M03 - PASSWORD
P03.01 Enable passwords
P03.02 User level password
P03.03 Advanced level password
P03.01 – If set to OFF, password management is disabled and the access to setup parameters and command menu is allowed.
P03.02 – When P.03.01 enabled, value to be specified to get user access. Refer to Password Access chapter.
P03.03 – Like P03.02, but referred to advanced access.
M04 - INTEGRATION
P04.01 Integration mode
P04.02 Power integration time
P04.03 Current integration time
P04.04 Voltage integration time
P04.05 Frequency integration time
P04.01 – Selection of average reading calculation method:
Fixed = Readings are integrated for the set time. Every time the integration time elapses, the Average value is updated with the result of the last integration.
Shift = The instantaneous values are integrated for a period of time equal to 1/15th of the set time. Every time this interval elapses, the oldest value is replaced with the new one just calculated. The average value is
updated every 1/15th of the time set, considering a time-sliding window that groups the last 15 calculated values, with a total length equal to integration time setting.
Sync = Like fixed mode, but the integration intervals are started by an external digital input programmed with Synchronisation function.
Bus = Like fixed mode, but the integration intervals are started by synchronising messages on the serial bus.
P04.02 – Average readings integration time, used for active, reactive and apparent power.
P04.03, P04.04, P04.05 – Readings integration time (AVG) for the corresponding measurements.
M05 - HOUR COUNTER
P05.01 Hour counter enable
P05.02 Partial hour counter enable
P05.03 Channel number (x)
P05.01 – If set to OFF the hour counters are disabled and the hour meter page is not shown.
P05.02 – If set to OFF, the partial hour counter is not incremented. If ON, time is incremented as long as DMG is powered. If set to an internal variable (INPx-LIMx-BOOx), time increments only while a programmed
condition occurs.
P05.03 – Number of the channel (x) of the variable eventually used in the previous parameter. Example: If the partial hour counter must count the time during which one measurement is above a certain threshold, e.g.
defined by LIM3, then it is necessary to program LIMx in the previous parameter and channel 3 in this parameter.
M06 - TREND GRAPH
P06.01 Trend graph measurement
P06.02 Autorange
P06.03 Full scale value
P06.04 Full scale multiplier
P06.01 – Selects the reading to be shown on trend graph page.
P06.02 – Choice between automatic range or fixed range defined by the user.
P06.03 – Full scale range value. The unit of measure is the one defined by the selected reading.
P06.04 – Full scale value multiplier.
UdM Default Range
English English
Italiano
Francais
Espanol
Portoguese
% 50 0-100
% 100 0-100
% 30
sec 30 5-600
sec 60 OFF / 10-600
VL-L VL-L / VL-N ...
INST INST / HI / LO /
AVG / MD /GRAPH /
sec 0.5 0.1 - 5.0
UdM Default Range
OFF OFF-ON
1000 0-9999
2000 0-9999
UdM Default Range
Shift Fixed / Shift
Sync. / Bus
min 15
min 15
min 1
min 1
UdM Default Range
ON OFF-ON
ON OFF-ON- INPx-
LIMx-BOOx
1
UdM Default Range
kW (tot) VL-L (eq) AVG
AVG kW (tot) AVG
kvar (tot) AVG
kVA (tot) AVG
ON OFF-ON
1000 0-1000
x1 x1 - x1k - x1M
G
B
0-50
1-8
1-60
1-60
1-60
1-60
1-8
11