Eu Declaration Of Conformity; Technical Data - EUCHNER TR Serie Mode D'emploi

Operating Instructions
Safety Switch TP...
Notes about
The following information applies to devices
with cable entry:
For use and application as per the requirements
of a copper wire for the temperature range
60/75 °C must be used.
The following information applies to devices
with plug connector:
This device is intended to be used and applied with
a Class 2 power source in accordance with UL1310.
Connecting cables for safety switches installed at
the place of use must be separated from all moving
and permanently installed cables and un-insulated
active elements of other parts of the system that
operate at a voltage of over 150 V. A constant
clearance of 50.8 mm must be maintained. This
does not apply if the moving cables are equipped
with suitable insulation materials that possess an
identical or higher dielectric strength compared to
the other relevant parts of the system.

EU declaration of conformity

The declaration of conformity is part of the oper-
ating instructions, and it is included as a separate
sheet with the unit.
The original EU declaration of conformity can also
be found at: www.euchner.com
Service
If servicing is required, please contact:
EUCHNER GmbH + Co. KG
Kohlhammerstraße 16
70771 Leinfelden-Echterdingen
Germany
Service telephone:
+49 711 7597-500
E-mail:
support@euchner.de
Internet:
www.euchner.com

Technical data

Parameter Value
Housing material Reinforced thermoplastic
Degree of protection
acc. to IEC 60529
Cable entry IP67
Plug connector SR6/SR11 IP65
Mechanical life 1 x 10 operating cycles
6
Ambient temperature -20 ... +55 °C
Degree of contamination
3 (industrial)
(external, acc. to EN 60947-1)
Installation orientation Any
Approach speed, max. 20 m/min
Extraction force (not locked) 20 N
Retention force 10 N
Actuating force, max. 10 N
Actuation frequency 1,200/h
Switching principle Slow-action switching contact
Contact material Silver alloy, gold flashed
Connection
TP... Cable entry
TP...SR6 Plug connector SR6, 6-pin+PE (PE
not connected)
TP...SR11 Plug connector SR11, 11-pin+PE
(PE not connected)
Conductor cross-section
0.34 ... 1.5 mm²
(flexible/rigid)
Operating voltage for optional
L024 24 V
LED indicator
Rated insulation voltage
TP..., TP...SR6 U = 250 V
i
TP...SR11 U = 50 V
i
Rated impulse withstand voltage
TP..., TP...SR6 U = 2.5 kV
imp
TP...SR11 U = 1.5 kV
imp
Conditional short-circuit
100 A
current
Switching voltage, min.,
12 V
at 10 mA
Utilization category acc. to EN 60947-5-1
TP..., TP...SR6 AC-15 4 A 230 V /
DC-13 4 A 24 V
TP...SR11 AC-15 4 A 50 V /
DC-13 4 A 24 V
Switching current, min.,
1 mA
at 24 V
Short circuit protection
(control circuit fuse) 4 A gG
acc. to IEC 60269-1
Convent. thermal current I 4 A
th
Solenoid operating voltage/solenoid power consumption
TP...024 AC/DC 24 V (+10%/-15%) 8 W
TP...048 AC/DC 48 V (+10%/-15%) 8 W
TP...110 AC 110 V (+10%/-15%) 10 W
TP...230 AC 230 V (+10%/-15%) 11 W
Duty cycle 100%
Locking force F
max
TP1/TP2/TP3/TP4 F = 1,300 N
max
TP5/TP6 F = 800 N
max
F
Locking force F
max
Zh (F = )
Zh
acc. to EN ISO 14119 1.3
TP1/TP2/TP3/TP4 F = 1,000 N
Zh
TP5/TP6 F = 600 N
Zh
Reliability values acc. to EN ISO 13849-1
B
3 x 10
10D 6
at DC-13 100 mA / 24 V
8