Initial Battery Charge; Battery Recharge - Peg-Perego JOHN DEERE GATOR XUV 550 Utilisation Et Entretien

INITIAL BATTERY CHARGE

!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery charger to battery.
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP
EDGE HAZARD.
BATTERY IS INCLUDED AND MUST BE INSTALLED; see instructions 42 - 50
1 • Insert black windshield frame onto the clear windshield until the clear center pin snaps into the hole.
2 • Place windshield on the hood as shown.
3 • Attach windshield to hood with 2 screws. (Install dash decals before installing steering wheel)
4 • Assemble the 2 steering wheel components and press firmly together.
5 • Place steering wheel onto steering column tube and align bolt holes.
6 • Insert bolt into round hole and locknut into hexagon shaped hole. Tighten bolt with screwdriver.
7 • Install the front grill into hood until it snaps into place.
8 • Attach front bumper - battery cover; (A) place lower bumper holes onto chassis pins and (B) rotate up until it snaps closed.
9 • Secure with screw (after battery is charged) to keep children away from battery.
10 • Headlight lens; apply chrome decals, then press amber lens into sockets
11 • Headlight lens; apply chrome decals, then press clear lens into sockets
12 • Press 4 small hubcaps into wheels.
13 • Attach fuel tank cap onto filler neck.
14 • Insert filler neck into the opening on the driver's side chassis (below seat).
15 • Turn it 90° clockwise until it locks.
16 • Install black trim to dump bed (both sides).
17 • Assemble roll-bar mesh to roll-bar and secure with the small screw provided.
18 • Place roll-bar ends into the holes at the front of the dump bed and push down.
19 • Secure it with the 2 screws provided.
20 • Install tailgate; insert tailgate left pin into left hole in bed; gently but firmly press down on right side until right pin enters right hole.
21 • Install bed: Forcefully remove the 2 oval pins from the 2 black rear dump bed hinge brackets.
22 • Place the round hole end of the black bracket into the hinge flange on the chassis; the oval hole to the rear and the ¼" flat extrusion pointing down into the
chassis slot.
23 • Align the holes and insert the round black plastic pins (both sides).
24 • Set the bed on the chassis; align the oval bracket holes with the round bed flange holes (both sides).
25 • Insert oval plastic pins to secure the bed to the chassis (both sides).
26 • Connect the spring and the red fastener as shown in the figure. Lift up the piston and insert the red fastener into the upper part as shown in the figure.
27 • Keep the piston up. Align the piston hole with the FRONT hole of the bed flange (see figure)
28 • Secure it with the red plastic pin.
29 • Apply the two armrests to the sides of the double seat.
30 • Secure both armrests with the three screws provided.
31 • Place the double seat in line with the appropriate holes, depending on the height of the child, and secure it from underneath with the four knobs. The Gator
can be set up in 4 positions (see diagram).
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY. THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM
THE VEHICLE.
32 • Unscrew the battery cover.
33 • Unfasten the battery cover and open it.
34 • Connect the battery plug to the electrical system. The vehicle is ready to use.
35 • A - DRINK HOLDER: a conveniently placed drink holder is located on the dashboard.
B - HAND GRIP: passengers can hold onto the hand grip for maximum safety while using the vehicle.
36 • ELECTRIC ACCELERATOR with SmartPedal Technology™. When accelerator is pressed completely down, forward motion is activated. When pedal is
released halfway, neutral coasting action is engaged. Brake activates automatically when the child takes his foot off the accelerator. New SMARTPEDAL
TECHNOLOGY feature allows for longer runtime and more realistic driving.
37 • TAILGATE: The load box is supplied with a tailgate with drop-down opening. To lower the tailgate, pull it up and roll it outwards.
38 • DUMP BED:The dump bed can carry objects for a maximum of 22 lbs.To operate the dump bed, pull upward on red latch and unlock it as shown in the figure.
39 • GEARSHIFT POSITIONS: 3 positions; Center; 2¼ mph forward, Up; 4 ½ mph (NOTE: vehicle is shipped with 4 ½ mph speed LOCKED-OUT for SAFETY.
Parents must follow instructions 40 and 41 to activate high speed. Down; reverse (gearshift must be held in the down position for safety; we never want a
child to step on the accelerator and go in reverse when they think they will go forward).
40 • Unscrew safety screw to release the high speed lockout pin.
41 • Secure the high speed lockout pin in the second hole as shown in the figure. The vehicle can now be shifted to 2nd speed. If you do not want your child to use
the second speed, secure the high speed lockout pin in the first hole.
42 • Unscrew the battery cover.
43 • Unfasten the battery cover and open it.
44 • Release the battery lock
45 • Disconnect the plugs and remove the discharged battery. Insert a fully charged battery and repeat the procedure in reverse order.
46 • Unfasten the battery cover and open the battery compartment. Disconnect the electrical system plug (A) from the battery plug (B) by pressing on the sides of
the plugs and pulling apart.
47 • Plug the battery charger into a household electrical outlet. Connect battery plug (B) to charger plug C. NOTE: Press firmly until it snaps into place.
48 • After battery has finished charging (full charge takes 18-24 hours), disconnect battery charger from the electrical outlet and then disconnect the battery plug
(B) from the charger plug (C).
49 • Reconnect electrical system plug (A) to battery plug (B). NOTE: Press firmly until it snaps into place.
50 • Close the battery compartment, fastening the battery cover shut. ATTENTION: Always make sure that the battery compartment is closed and locked after
carrying out any operations inside it.
ASSEMBLY INSTRUCTIONS
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
BATTERY REPLACEMENT (if you've purchased a 2nd battery for extended riding time)
BATTERY INSTALLATION

BATTERY RECHARGE