Metabo SM 5-55 6.31619 Notice Originale page 11

Always attach the depth stop and supplied handle
with strip guide before starting work.
When dismantling the screwdriver magazine,
remember that the sliding piece is spring-loaded.
Dismantle with care so that the sliding piece does
not eject from the tool and strike people or objects
in the direct vicinity.
Only use screw types and dimensions that are
listed in the Technical Specifications and make
sure that they are suitable for the material being
processed.
Always use genuine Metabo screwdriver bits and
replace bits immediately if they become worn or
damaged. (see section 10 Accessories).
Switch the screwdriver to "Clockwise" rotation.
We do not recommend removing screws ("Anti-
clockwise" rotation) with the screwdriver magazine
attached.
Before removing screws, do not detach the
complete screwdriver magazine from the screw-
driver as the mounting is not designed for frequent
removal and reattachment and will wear prema-
turely.
Instead, slacken the clamping screw (1) and then
detach the screwdriver magazine from the adapter
(2). Then remove the screw. Slide the screwdriver
magazine over the screwdriver bit (3) on the
adapter (2) and push against the adapter (2). Align
the screwdriver magazine on the screwdriver
accordingly. Tighten the clamping screw (1) again.
Switch on the screwdriver before inserting any
screws to improve machine handling.
5 Overview
See illustration on page 3 (please unfold).
1 Clamping screw
2 Adapter
3 Screwdriver bit
4 Standard screwdriver depth stop
5 Quick-release screwdriver coupling
6 Sliding piece
7 Depth stop
8 2 screws for depth stop adjustment
9 Adjusting ring (screw depth/countersink
depth)
10 Ratchet wheels
11 Screw strip
12 Strip guide
13 Handle
For cleaning, maintenance (see page 4):
14 Screw (with roller)
15 Spring guide
16 Pressure spring
17 Crosshead screw
18 Pin
19 Ratchet wheel unit
6 Commissioning
See illustration on page 3 (please unfold).
6.1 Attaching the magazine to the screw-
driver
- Remove the standard depth stop (4) from the
screwdriver (read the screwdriver Operating
Instructions).
- Insert the screwdriver bit (3) into the quick-
release coupling (5) on the screwdriver (read the
screwdriver Operating Instructions).
- Attach the screwdriver magazine with adapter
(2) to the screwdriver bit (3) on the screwdriver.
Note: the adapter (2) can be attached to the
screwdriver in 4 positions (rotated in 90° incre-
ments). Slacken the clamping screw (1) to align
the screwdriver magazine parallel to the screw-
driver. Tighten the clamping screw (1) again.
6.2 Adjusting the depth stop (7)
The numbers on the depth stop (7) correspond to
the screw lengths (mm) that the tool is capable of
inserting.
The depth stop (7) must be adapted to the
length of the screws being inserted.
- Slacken the two screws (8) and adjust the depth
stop (7) according to the length of the screws
you wish to insert.
- The depth stop (7) is set correctly when the
number indicated (e.g. "35") is the same as the
screw length (8).
- Tighten the two screws (8) again.
6.3 Presetting the screw depth
The screw depth must be adjusted every time the
screw size changes and the position of the depth
stop (7) is modified.
- Push in the depth stop (7) up to the stop and
hold in this position.
- The tip of the screwdriver bit (3) should protrude
approx. 3 mm beyond the depth stop (7).
- If necessary, adjust the screw depth by turning
the adjusting ring (9):
• To increase the protrusion distance of the
ENGLISH
ENG
11