Principle Of Operation; Technical Details - STAMOS S-LS-17 Manuel D'utilisation

CAUTION
General safety information for the use of electrical devices:
To avoid injury from fire or electric shock, please ensure compliance with safety instructions when using
this device. Please read the instruction carefully and make sure that you have understood them well. Keep
the manual near the equipment to be able to read it at any time. Always use current sources connected
to the ground and providing the necessary voltage (indicated on the label on the device). If you have any
doubt, let an electrician check that your outlet is properly grounded. Never use a damaged power cable.
Do not open the unit in damp or wet environment, or if your hands or body are damp or wet. Protect
the unit from solar radiation. Use the device in a protected location to avoid damaging the equipment or
endangering others. Make sure the device is able to cool and avoid placing it too close to other devices
that produce heat. Before cleaning, disconnect it. Use a soft damp cloth for cleaning. Avoid using detergent
and make sure that no liquid enters the unit. No internal element of this device needs to be maintained by
the user. An opening of the device without our approval leads to a loss of warranty.
General safety information for the use of the device:
• The user manual should be kept close to the device and should always be accessible for the users.
Instruct your employees how to use the device properly.
• Make sure the hot air can circulate well and place the device more than 10 cm away from walls and
other electrical devices. Properly aerate the working area.
• Do not place the device close to combustible materials.
• When first using the device the heating element may produce a light smoke. This is absolutely normal.
Simply ensure that the smoke can evaporate and that a good aeration is provided.
• Some parts of the device can get extremely hot. To avoid any injuries, be careful whenever you come
into contact with the device.
• Clean the device regularly to avoid permanent accumulation of dirt.

TECHNICAL DETAILS

Model
Voltage (V)
Rated current (A)
Power (W)
Work temperature (⁰C)
Storage temperature (⁰C)
Temperature range (⁰C)
Output power (W)
Temperature stability
Tip resistance to ground
Tip-to-ground voltage
SMD REWORK STATION
Temperature range (⁰C)
Output power (W)
Temperature stability
Airflow (L/min)
10
EN
6134 S-LS-17 | 6135 S-LS-17 Basic
230 ~50Hz
6
700
0/+40
-20/-80
SOLDERING STATION
100-480
±2 ⁰C
75
<2 Ω
<2 mV
100-480
650
±2 (⁰C)
120
USAGE PURPOSE
The device is designed for:
1. Different kinds of soldering, de-soldering of the electronic components such as: SOIC, CHIP, QFP,
PLCC, BGA, SMD, etc.
2. Shrinking, paint drying, adhesive removal, thawing, warming, plastic welding.
Any damage resulting from a non-conform use of the device is to be paid by the user!

PRINCIPLE OF OPERATION

12
11
13 8
10
9
3
1 2
1. SMD rework gun cable
2. soldering iron connection socket
3. airflow volume adjustment knob
4. SMD rework gun working indicator
5. SMD rework gun temperature setting knob
6. soldering iron temperature setting knob
7. SMD rework gun switch on / off
8. soldering iron switch on /off
9. SMD rework gun working (heating) indicator
10. SMD rework gun temperature display
11. soldering iron working (heating) indicator
12. soldering iron temperature display
13. SMD rework gun working mode switch – automatic mode / manual mode
BEFORE FIRST USE
Upon receipt of the goods, check the packaging for integrity and open it. If the packaging is damaged, please
contact your transport company and distributor within 3 days, and document the damages as detailed as
possible. Do not turn the package upside down! When transporting the package, please ensure that it is
kept horizontal and stable. Please keep all packaging materials (cardboard, plastic tapes and styrofoam), so
that in case of a problem, the device can be sent back to the service centre in accurate condition.
Disposing of packaging
The various items used for packaging (cardboard, plastic straps, polyurethane foam) should be conserved,
so that the device can be sent back to the service centre in the best condition in case of any problems!
EN DE
6
7
5
4
1
11